We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi,
So this may seem like a stupid question but here goes. I've been trying to learn how to implement an IoT solution.
While trying to learn more about MQTT protocol...
Hi,
I'm trying to build the example found here: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/uart
and the build is failing with this...
Hi!
I've been trying to connect the nRf9160 to an AWS IoT account following the directions here https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples...
Hey guys I am using nrf52840 dongle for scanning ble beacons. I want my dongle to be power optimized in a way that it starts scanning for 10 sec and then go to sleep for one...
Hi,
I am working on nRF52DK. The Bluetooth MAC address is stored into the Flash during the pairing sequence. Can some one provide me the links to understand the storing...
hello
hi
I connect AT24C02 EEPROM with nrf52dk.
I connect SCL to 27 pin ,and SDA to 26 pin.
I open twi_master_with_twis_slave sample code and make some changes(i2c...
Hello there;
We want to develop a project using the nrf52 series. We have two nrf52s. The first one is in the center and connected to the mains and there is no battery problem...
Hi there i have serius problem in gettimng my nrf52840-dk to work, i am set up in Visualstudio code on a mac, avery thing compiles and seem to upload but nothing happens afterward...
nRF connect v1.0.0 SDK
I am using UART peripheral to communicate with GPS module and we want to put device in PSM (Power saving mode) but we are not able to disable UART...
I,m using nrf51822 , Softdevice S110 and SDK V10. i have and spi interface with SST26VF064B (8MB flash) . SPI is running at 4MHz frequency and there is 8us delay between each...
I have a new board with a STM32L47 running mbed OS. There is an nRF52811 connected via SPI. I simply want to verify that the nRF52811 is connected properly and can be communicated...
Hi there,
On our test jig, we are using two IO pins of nRF52832 as UART lines that goes to a UART dongle to the PC. When we pull the power plug to the Nordic chip and have...
I deleted nrf-related files and set up nrf programs from a scratch following Get Started Assistant of nRF Connect v3.0.0
I've got this warning when I opened a project by...
This is for a current project on SDK 15 and nRF52832.
My project has several configuration parameters, which exist as BLE attributes.
I'd like to make them persist across...
