Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi, I want to power the system off when a a characteristic is written. I do so by calling sleep_mode_enter function listed below. When sd_power_system_off is called the system...
hi
i program the hex of nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard into pca10056,it run ok .if i don't connect it by phone，and than press button1...
Hello,
I want to test the Thingy Mesh Provisioning Demo v0.7 with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo...
Hello everyone, recently i was trying to figure out the best way how to send a large amount of data from ble peripheral to the central (Android device in this case) and thanks...
Hi,
I want to add FDS basedon dimming_serve example ,However,after fds_init(); it not jump to fds_evt_handler but stop wait .
The below is my code:
And The Bellow...
Hi all.
First I would like to apologize for any mistake because I'm posting first time here.
I'm using Visual Studio Code (VSC) to evaluate the blinky example from nRF5...
I recently had the need to communicate with a device over I2C. I'm using the nRF52 as the master. Everything works fine, but power is a concern. I am putting the processor...
Hello,
I have the same problem as this post . The difference is my SPI is sending out junk instead of stucking. I have tried the solution in the original post but no avail...
We bought 3x nRF52833dk (pca10100). Because the nRF5SDK V16 has only a few pca10100 examples we searched this forum and followed the advice: Change the "Linker->Sections Placement...
Hello,
I'd like to look at the Zigbee network traffic to/from/between IKEA Trådfri devices, but am unable to see any traffic when using nRF Sniffer from Wireshark. Unfortunately...
Hi,
I have an nRF52840 Development Kit, and am trying to control an IKEA Trådfri bulb. I'm following the commands from the SDK documentation , but it feels like they're...
So I'm trying to write a value to a characteristic I have set up as in the code below (figure 1), using the code further below (figure 2).
The sd_ble_gatts_hvx call is coming...
Hello
I would like a suggestion on the best architecture to collect data from multiple sensors in a room. Let me explain my need.
I have a room where we place multiples...
I'm trying to understand how RSSI measurement works.
According to datasheet if I understood correctly I have to issue a " TASKS_RSSISTART " command and wait for the corresponding...
