I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
I need to set HEX value (uint8_t value[7] = {0x56,0x45,0x52,0x53,0x49,0x4F,0x4E};) on my custom character to be read by my phone. but the value that is displayed on my character...
Hi,
1. I have been trying to measure the current consumption of the development board of nRF9160 in PSM mode, however, until now I could have not understood the role of...
Hi all,
I'd like to pass bootloader version (2bytes) from bootloader_util_reset function (bootloader) to the main of application. can help me to acheive that?
Thank...
Hello,
We are facing recently an issue that is very weird because it is not occuring every time. Indeed, the issue occurs after a DFU update, sometimes when the application...
My nrf51 DK Board is not detected by Keil as jlink probe, but with other tools. As a result I am unable to download demo projects to my board.
unmodified nrf51 dk has...
I'm working in SDK 14.2, and trying to send a single byte over SPI between two NRF5 boards using the SPI peripheral examples (1 master and 1 slave). However, SPI always seems...
Hello!
There are no hex files that are pre-made for the ble_app_interactive example. When I use VMware to run a Linux environment on Ubuntu to get an executable with gcc...
Hello,
I want to configure my nRF52840 development kit for counting input pulses on one of the GPIOs (Pin 13) in this case. I am using SEGGER Embedded Studio as IDE.
Here...
Hello,
we have a strange proglem with nrf52811 on an own board
after uart initialization and connecting the scope (Saleae) probe to the RX pin the device outputs fatal...
Hi,
I have a ARM core device like raspberry pi / orange pi etc, where I run a build and deploy server - basically compiling code and flashing to a target.
I have the...
We are trying to use serial port library for simple UART comms in IRQ mode at 115200, but experiencing what looks like stuck TX interrupt. PCA10040 with SDK 15.3.
In the...
I'm using nRF Connect v3.0.0 to run Getting Started Assistant v0.9.3 and get a message it is only compatible with 2.4.0 (very old). I can install and verify Tool Chain except...
Hi
I am trying to connect and bond a nrf52832 to Galaxy S6, Android 7.0 by OOB / NFC with the ble_nfc_pairing_reference_pca10040_s132 example.
I selected LE Secure Connections...
Hi nordic,we want to config nrf52832 as a wireless full-duplex serial port transmission module through nordic proprietary protocol，so the module can send and receive data...
