I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
We attempted to deploy an Edge Impulse machine learning model on the nRF5340 DK for a simple test project. The model was trained using labeled IMU data (x, y, z) and used...
I know this pin is used in QSPI even after disabling the QSPI I am unable to toggle the GPIO what is the reason.
And this the sane pin I'm using for I2C that's not working...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working with the nRF9160 DK and running the AWS IoT sample from the nRF Connect SDK v2.7.0 ( 5cb85570ca43 ). The device connects to the network and AWS IoT Core...
Project (NCS v2.7.0):
We are working on an application that requires time synchronized sampling of sensor data from 4 nRF52840 devices. The sensor data is then streamed...
In the specs of npm1300 PS, it is suggested that the ADC can measure VBAT, VBAT_7V range, NTC, DIE_TEMP, VSYS, IBAT. However, in the interrupt configuration reported in 7...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
Hi all,
I'm working with the nRF9160 DK and running the AWS IoT sample from the nRF Connect SDK v2.7.0 ( 5cb85570ca43 ). The device connects to the network and AWS IoT Core...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Hi All,
we are deciding which chip to buy in order to make our AoA trasmitter (CTE packets).
According to https://www.nordicsemi.com/Products/Wireless/Bluetooth-Direction...
Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
Hello forum ,
Here i tried to write and read from flash qspi w25q64 but read and write both are failed ..i m using nrf52840 kindly pls help me for read and write
