We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
SDK: 15.3.0 Sample: ble_app_hids_keyboard Device: EYSHJNZWZ (nRF52832)
I have a question about HID. In the sample program "ble_app_hids_keyboard", the following values are...
SDK: 15.3.0 Sample: ble_app_hids_keyboard Device: EYSHJNZWZ (nRF52832)
I have a question about HID. In the sample program "ble_app_hids_keyboard", "report_map_data" stores...
Hi,
I am measuring a frequency using the ADC (200ksps) and saving the samples into an array. I save 128 samples then move that data to the fft module to check what the signal...
Currently, debug probes - STLink, JLink, OpenOCD, Black Magic Probe, DAPLinkda, etc. connect to a host PC over a USB, serial or network port and then connect to a target ...
I get ACI_BOND_STATUS_FAILED_ENCRYPTION_KEY_SIZE error when I try to bond my nrf8001 peripheral to my iPhoneX. The min and max key sizes are set to 7 and 16.
Any Idea?
Hi,
I'm using the ble_app_uart example as a starting point for my project. Basically I want to program the nRF52 DK to receive data from another device via UART, store them...
Hi Nordic,
I'm working on a project with very limited board space. I'd like to have the option for both SWD and GPIOs to share the same test points on the board. Ideally...
There is an issue in SDK for Thread & Zigbee 4.1.0 release. It does not appear in previous releases. The problem manifests itself as higher current consumption, as shown in...
I flashed nrf52840 usb dongle via SWD and now it can't go to DFU mode even if I press reset.
Green and blue leds are constantly blinking. How can I go to DFU mode in that...
Hi all,
I am developing ADC functions with Mynewt on nrf52 DK PCA10040 board.
The working example code based on SAADC driver nrfx 1.7.0 won't work on nrfx 2.1.0.
Example...
Hi Devzone:
I have been testing flash storage project.
in my code I have declared a one page flash at 0x40000 for my own use:
And in flash_placement.xml I have inserted...
I must be doing something obviously wrong but I just can't see it.
I'm trying to create a PPI linkage between the UART RXDRDY event and a timer working in counter mode so...
hello
i am working with nrf52832, s132, sdk 16.0
i am trying to init 3 channels with OVERSUMPELING and BURST enabled:
"
nrf_drv_saadc_config_t saadc_config;
...
