Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
Hi,
I understand there have been a few changes in the nRF Connect SDK with regards to Secure Boot and SPM.
I've been stuck for many hours trying to understand why I'm...
Hello,
I'm facing an issue when i want to delete some file in my FDS file system. Indeed, sometime, i can find dupplicated file with the same file id and the same record...
hi ,
i just realized that i damaged my NRF52 dev kit debugger chip. it is heating up and not working . the rest of the circuit including NRF52832 are fine. is there any...
I am using sparkfun nrf52832 breakout. I am new to this. I don't have a JTAG programmer so I cant program with keil. Is there an alternative solution for the software used...
I was using Sparkfun nRF52832 board to test my application, programming it with FTDI over Arduino IDE. Now I made my own PCB and found out that the IC doesn't have bootloader...
HI there! I am currently having some issues trying to add a custom 16 bit service to my nrf51822 project. Basically I am trying to make a dummy peripheral that I need for...
I have a nrf51-DK. I am trying to get a PWM signal on one pin. Here is my code:
static volatile bool ready_flag;
void pwm_ready_callback(uint32_t pwm_id){ ready_flag ...
is it possible to send ip packet form thread device with destination of non-thread device like ble (i gave ble device hardcoded ip) without border router ?
if yes i want...
Hello,
I am trying to flash my application to my NRF51422. In short, the application is a combination of the ble_app_uart and twi_scanner examples, I am reading data from...
Hello
I'm facing with printf over uart problem in my app. Application based on uart example from SDK 15.2.
However, it happens that printf function prints message to uart...
Hi,
On the latest nrfConnect SDK and zephyr, I started my application based on MQTT and AWS_FOTA samples.
The BSD socket function zsock_getaddrinfo sometimes returns a...
Is there at least one twi example available that uses pca10040e? Not seeing one in sdk15.0 for SES.
I can get the code working for pca10040 on s132 but not for nrf52810...
Hello,
I am new to nrf52 840 SDK, and currently working on Beacon code and really need help to fix some aspect of this code. I have a beacon code and would like to add custom...
Hi,
I'm using 3 AIN pins to read analog readings. However, when I go to sleep mode, I want the current to be as low as possible.
I notice that the AIN pins (saadc) is...
Hi everyone, recenly I had adquired a nrf52840 dk for testing how to work the BLE module. The problem was that in the first attemp the nrfGo showed that message:
I have...
