i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
I'm using Windows 10 latest updates installed.
I can successfully build v0.4.0 but none of the other releases of lte_ble_gateway
The common error is as below, any help...
Hello,
In our project there is a problem that we encountered is happening when the Nordic BLE mesh advertising and connectable advertising for GATT connections are enabled...
Dear Nordic.
I am manufacturing PCBA product using nRF52810-QCAA
My customer request to me about environment and Minerals report
I need three type of documents as...
Hi all,
I am trying to "add" the DFU bootloader to my application and I have some questions regarding it:
my thought are:
add to DFU bootloader example code, part...
Hi, After compiling the at_command example form the new release v1.0.0 and updating the nRF connect tool to version 3.0.0 I get the something that looks like bad baud rate...
I am using J-Link debugger.
I am programming nrf51822. On the Jlink commander my desktop sees my J-Link Lite CortexM device.
When I try the run an example on keil5 I got...
Hi All,
I used app_uart_fifo.c and it worked however RX is not good so I switched to LIBUARTE.
The RX part is good with LIBUARTE however when TX traffic is high nrf_libuarte_async_tx...
Hi,
I am using the nrf52832 dk
i am using the uart code from the sdk.
how do i clear the rx_buf and tx_buf (buffers) and set the pointers to the beginning of the buffers...
I have read through the USBD section in the nRF52820 datasheet and I think I cannot do what I need, but wanted to confirm I am not missing something.
I would like to make...
Hi,Master:
See below:
BAT + = 3.88V
a).When I removed the MCU:BAT_ADC = 2.556V
b).When I soldered the MCU:BAT_ADC = 2.28V,Why is there a 270mv voltage drop?
In the...
Hi, nRF9160 modem firmware V1.0.0 avalable from nordicsemi.com.
"Please use nRF Connect Programmer to update modem firmware."
it means that open nrf connect and choose...
Hey there,
I am having a strange issue where once I connect to a PCA10031 device using the Bluetooth low energy app (v2.2.1) the entire screen turns white just after the...
I would like to setup a development environment for the Thingy. I see there is a User Guide geared towards demoing the example application, but there isn't a specific getting...
Hello,
Currently, I am using NRF52832 and nRF5_SDK_15.2.0. Also, I am using FreeRTOS.
I disabled softdevice by calling nrf_sdh_disable_request() before goes to sleep...
