i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
I have combined light switch client and ble_app_uart example by following this guide and this case ,but after I added the codes :
#define MESH_SOC_OBSERVER_PRIO //<set...
Hi,
I am developing stuff for a bike and need the Bluetooth Cycling Power Service 0x1818
I found the 0x1816 Cycling Cadence and Speed
Has anybody developed this service...
Hello I'm a beginner and I try to use the DFU. I use the documentation and I can send my init packet without any problem. But when I try to send my Firmware I have 2 problems...
Hi,
Our system is based on the nrf52832 with SDK BLE_2.0.1 for the mesh. I have few queries as per below,
1)It would be great if you could suggest any vendor who is working...
When Going into Sleep, I see peaks of 12mA every 30ms (see image) I'm assuming I can adjust that changing the connection interval settings. I have my Connection intervals...
I'm having some issues with the freeRTOS example in SDK 15. I've always seemed to find a hardfault which limits the MTU size to 176. Now when I try and set the connection...
Hi,
I have a question regarding fast/slow advertising
I'd like to advertise for 180s using a 100ms interval, then switch to a 1s interval, preferably for ever. I set...
I would like to use ADXL335 accelerometer in this nrf52832 custom kit Hackable . I don't have a J-Link but i have this custom programmer Bumpy which is based on the Black...
Hi,
How can wake my nrf52832 based module from system off sleep mode. i am using ' nrf_pwr_mgmt_shutdown()' / ' sd_power_system_off (); 'function to put the device into...
softdevice 6.0.0 SDK15.0.0 How do I use ble_app_hrs sample code add buttonless_dfu function? I flow the steps, but I am fail. 1. In ble_app_hrs project... add nRF_DFU folder...
Hi Support team,
In this application note, solder paste type 4 has 25 to 45 micron particle size range while IPC J-STD-005 as attached stated type 4 has 80% Minimum between...
hi.
I used mergehex.exe to combine the hex of softdevice, bootloader, and application into one, but the board is in DFU state and the application does not start.
I am...
Hi! I'm developing on nRF51 with SDK 11 and trying to extend our application with buttonless BLE DFU support. Due to limited flash memory, we could only use single bank ble...
