I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello fellow bit jugglers!
We are developing an application for a nRF52805 on a nRF52-DK board, using NCS.
NCS version: 1.5.1
Zephyr version: 2.4.99
BLE controller...
Hi,
I want to run the Thread MQTT-SN Publisher and Subscriber example using the nrf52840 DK and the nrf52840 Dongle I have on hand.
I was able to sucessfully build and...
Hi, I'm trying to use BLE/Thread Multiprotocol for BLE RSSI scanning and send values using Thread, is it possible to use BLE and Thread(FTD) concurrently with out time-slice...
Hi all, Using SDK 17.0.2, on a Laird BL653. I've been messing with creating variable PWM sequences and found an issue where a 100%->0% duty cycle transition does not occur...
I once used nRF Sniffer with my nRF51822 module. I see that everything has updated since - Wireshark, Sniffer plugin (now is Python 3.4+), Sniffer firmware. As I can see,...
Hi all, i don't have any issues I am just now using the nRF Connect power profiler after a ~4 month break. WOW, the major update is absolutely phenomenal. The graph is very...
Dear Nordic DevZone community,
we modified the LwM2M client example to fit our application in a LTE-M network. Now we are trying to get GPS to work while still being able...
Hi.
I'm using nrf52832 with SDK-17, and the ESB example (esb_tx and esb_rx)
I'm not much experience in nrf development recently I have a project related to ESB to transmit...
Hello,
In nRF52832, we use nRF Connect to read the board, save the program data into a hex file, and send the file to other developers. They can use nRF Connect to write...
I am using sniffer v3.1. I have installed the sniffer code on a nRF52840 dongle (PCA100059). When I insert this into the PC with windows 8.1 it appears as "nRF Sniffer for...
Hello,
In our product, the nRF9160 is configured to use LTE CAT-M1 and we are measuring the signal quality thorugh the AT+CESQ command.
After begin registered on the...
Hi: I have write a spi slave, and write a spi master on STM32, It can receive data from STM32,But I have no time to prepare the response data.
as the code below, I can receive...
I checked the SPI communication using the NRF52832 development board.
Based on the firmware of the previously developed NRF52810 product, the SPI operation code is applied...
Would like to interface a SPI ADC – MCP3461 via the nRF52840 serial peripheral interface master with EasyDMA (SPIM). I was not able to find whether or not there is an available...
