Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
refer an example for long lange demo in sdk.
i have found this example https://github.com/NordicPlayground/nRF52-ble-long-range-demo but in this nrf52840 boards are used...
Hi, What we would like to do is to store the firmware on one nRF52 MCU and do the DFU over BLE to the other nRF52 MCU. This means that the first nRF52 MCU needs to connect...
Hi Nordic,
my BLE peripheral with the nrf52840 and sdk 15.3 with s140 restarts if not connected after 180s. I assume that the reason is the .config.ble_adv_fast_timeout...
Hi,
I am trying to create a mesh network using nrf52832 for RGB lights. I am using nrf Connect SDK to build the project. Is there any sample code for RGB that can be integrated...
I have found that you cannot update MCUBoot unless you also have the NRF Immutable Secure Bootloader, If i have this then i cannot update the Immutable bootloader.
Is there...
We developed a ble hid mouse using ble_app_hid mouse example. When our mouse used in MAC os scroll wheel function is not working as expected i.e. when we scroll there is only...
Hi, We have an issue with custom devices in the field that have nRF52811, with s112 programmed. To sort out our issue we need to connect to the nRF52811 that is an advertising...
Nordic's BLE page ( https://www.nordicsemi.com/Products/Bluetooth-Low-Energy ) says the nRF5340 is the "ideal choice" for LE Audio. I can't seem to find any information on...
Hallo,
my nRF52840 and my nRF24L01 are receiving the same data in proprietary radio mode.
Several nRF51822 are sending mixed up data.
Within the nRF24L01 - radio Interrupt...
Hi,
I am completly new in nrf52, nrf-connect and zephyr environment.
I need to configure pwm channels that wont be used to drive led...
Most of thing is undestand for...
Sending a PSK like:
AT%CMNG=0,42,3,"1r0nm@n"
should result in failure, as that is not a valid hex string (as documented in nRF91 AT Commands). Currently this results in...
Hello,
I am trying to run the CCS881 sensor sample in my nrf9160 board. I have made changes to my project config file and main.c file as mentioned in
https://devzone...
I need to compare two ble_date_time_t structs to figure out if one is later than the other. So basically I need to check if rtc_datetime > expiration_datetime. Both rtc_datetime...
I plan on writing my own service (similar to NUS) but prior to that, I'd want to use all the existing APIs for initializing the GATT and BLE stack at least
I'm calling the...
Hi Team,
i have trying to create multiple serial port with debug log enabled in the sdk code sample but when i am going to init log_init a long with any UART / SERIAL...
