I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Helo Nordic support team,
I am supporting a client that has designed a product using the NRF9160 with GPS. The product has a small patch antenna mounted on the pcb board...
Hello. I am trying to build an project and I need to use RF module. And I have to Use pic18f45k22 with MikroC. But I couldnot. I have some 18f45k22 codes but dont work I dont...
Hello,
I need to retrieve the IP-Address of the modem, are there any convenient way I can do this?
AT commands maybe?
Appreciate any info on this.
With regards...
Hello
I am having rather odd problem with SWDIO pin shorted to ground. I am using Fanstel BT840x BLE module and I have never seen this issue on my custom board until last...
I see this line for cache enable register in application domain : infocenter.nordicsemi.com/index.jsp
NVMC built-in cache not supported (ICACHECNF, IHIT and IMISS registers...
I'm trying to test button less dfu on nrf 52840 dk. i am simply compile that hex ble_app_buttonless_dfu_without_bonds_s140_with_setting_page.h file with soft device s140 or...
I am building the coded bluetooth gateway using nrf52840 and ENC28J60. Integrated between two examples:
https://github.com/nrfconnect/sdk-nrf/tree/master/samples/bluetooth...
Hi to everyone!
I am working (with Keil uVision) on a custom PCB that includes the NRF52832 (MDBT42Q module) and some sensors from MAXIM INTEGRATED. There is a Sensor Hub...
Hello, I was told to make a new ticket after commenting on this ticket .
I am using SDK 14.2, S140 alpha, NRF52840. Segger IDE. I have been developing with this IDE & SDK...
Hello
I want to transmit location data to website using udp, the examples udp and gps are very good and I need combine in only one project but dont understand what files...
Hello,
The product specification for the nRF5340 peripheral chapter here mentions " The application core peripherals are accessible from the network core".
However in...
Hello I am using ncs version 1.5.0 .We are using nrf9160 dk version 0.15.0 & 1.0.0 for our development.Whereas we observed some issues like the network latching time is getting...
Hi, as part of my project i have 2 nordic 52dks one as a pheripheral (sending) and on as a client (recieving). where i am sening a buffer of 8, in the order
buffer[0] =...
Hello -
I am creating a new BLE Peripheral application with nRF52832 and S132 soft device. I would like to add the ability for the peripheral to force a disconnect with...
hii this is rohit vekariya
i am new in nordic , i am trying to use nrf52840 dongle for usb communication with PC my goal is get data from mobile app and send it to pc ,...
