Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hi,
Is it possible to upgrade a S112 v6.1.1 softdevice to the S113 v7.2.0 softdevice using BLE DFU?
I am getting the following error right after the SD + BL has been...
Hi folks,
I am playing around with the A-GPS sample.
I am trying to send the fix every five seconds to the cloud. This should be possible according to the webinar last...
At my system (production) there are 6 serial ports and 2 programmer (ARM-Flasher from Segger) connected.
The nRF Connect - Programmer only display 5 COM-Ports and NO Segger...
Hello,
I am starting a new project and we are using the following:
-NRF52840
-SDK v16.0.0
-pca10056 (NRF52849 DK)
After downloading the SDK, I was able to build...
Hi,
I am developing on nRF52840 using SDK version 15.0.3 and Softdevice version 6.11
I have observed that the once you initialize the app_uart using 'app_uart_init(...
Hi,
I want to identify the specific provisioned node among all n number of provisioned nodes using nRFMesh app.
Does any event will be appeared in sdk, after provisioned...
Hi, I am begginer, I work with SES, Mesh_v5.0.0, nRF5_SDK_17.0.2, and s132, SD v7.2.0. I started it two weaks ago. :)
I tryed the examples, Light switch , with server and...
Does Nordic have an example SW for transmitting and receiving data in BLE 5.2 connectionless isochronous communication mode? Is there a SoftDevice that would support this...
Hi, good morning , i am just wondering is it possible to send and recive data through ble faster than the coded examples please as i am sending gyrodata and its taking about...
Hello - I've google'd around a bit on this unsuccessfully...
I've successfully provisioned and configured an nRF Mesh network with mutliple servers and a single client,...
hi, I am working on the nrf52832 device, I have implemented the push button and I am able to detect button push and release but I want to notify the app when the push button...
Hi,
I am trying to interface nrf52832 with LoRa transceiver module sx1262. Can anyone please provide some sample code to check basic Tx/Rx of this chip. I am unable to find...
Hi,
I am looking for an example that uses the eDMA with the TWI in the 15.2 SDK on nRF52840.
My idea is to read out an external sensor using the TWI with as little processor...
Hi,
I would like to know how to set the service to NB-IOT Cat NB1,
and how then to set the UL subcarrier spacing to 3,75 KHz,
and how to fix the power to 23 dBm, not...
