I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does m_xfer_done need to be set to false before calling nrf_drv_twi_rx? If so, does while (m_xfer_done == false); loop need to be called on every read?
I'm developing a Bluetooth mesh device on a Window 10 machine using Segger Embedded Studio v4.52c on a nRF52832 chip using SDK16.0.0, Mesh SDK 4.1.0 and FreeRTOS.
in the...
Dear all.
I just got nRF52 DK and testing blinky based on KEIL and it works well.
I tried one test, IF BOOT/Reset, and nRF52 PDK is not working after below sequence. ...
Would it be possible at all to add a preset text string to the current advertising data, in an advertising-only module configuration, by changing the logical input of one...
Hi,
I've upgraded my SDK from 15.2 to 17.
After upgrading - I can't connect my device via NFC - it keeps disconnect with NRF_ERROR_RESOURCES .
I've tried to increase...
Hi
My goal is to create a USB HCI firmware that works on any custom board that exposes the USB port of a nRF52840. Based on the requirement for USB HCI it was clear to use...
Hi, I am working on an OTBR, nrf52840 connects to the router through SPI, I want to know how to upgrade 52840 through the router. The router use OpenWRT. p lease give me some...
Hi,
Our devices are getting randomly bricked by updating firmware through mcumgr in Zephyr. It happens on both the nRF91 and nRF52 chips when we run the latest nRF Connect...
It's strange, My nrf52840 can't boot up after power on,unless it was connected to JLINKRTTVIEW, If I disconnected the JLINKRTTVIEW, the device will stop running, Connect again...
Can anyone tell or give a pointer to info about RFCOMM vs. NUS (or any other vendor specific UART emulation service)?
Why are there vendor specific UART emulation services...
Referring to the Nordic message sequence chart in the following link:
https://infocenter.nordicsemi.com/index.jsp
(Software Development Kit -> Previous Versions of nRF5...
Hello!
I use SDK v17 and using the library and example code for the lsm9ds1 sensor.
github.com/.../nRF52-DK-and-LSM9DS1
'lsm9ds1_reg.c', 'lsm9ds1_reg.c' these two files...
Hello!
I am using ble adc scan mode example and successfully tested it with nrfconnect by sending my data from AIN3 . Now i want to send data of ble to raspberry pi bluetooth...
HI
Like to check on the usage of MQTT. We are connecting the nrf9160 to the network in eDRX.
During the interval, we may lose some message due to the lost of connection...