Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
We have 2 projects. 1 using an nRF52833 and the other using an nRF52840. In both circumstances we can cause a brownout condition. In order to remedy this situation i wanted...
Hello, regarding the NRF54LM20A board we made, during the low-temperature test, we encountered a problem where the log printing gradually slowed down and eventually froze...
NRF Connect extensions running within a flatpak VS Code on Ubuntu 25.10.
First of all, fixed the certificate not found issue that some folks have reported in other questions...
Is there a workflow white paper on how e-sim is used or is there documentation in the example workspace? If it's the latter is it easy to point this out? Thank yo.
Environment
I can see a Usage fault on MPSL Work with invalid PC ; addr2line shows Zephyr frames for some LRs and no symbol for an address in the SoftDevice/MPSL range....
Hi,
we are trying to get the psa attestation on the nrf54l15 to work. We have tried config options for hours but CONFIG_TFM_PARTITION_INITIAL_ATTESTATION always gets 'n...
In the NCS SDK, is it possible to implement periodic broadcasting of a certain number of data packets, for example, quickly broadcasting 3 data packets, then waiting for 10...
Hi everyone, I have a central firmware application connected to 2 peripheral devices: A and B.
I use the method bt_gatt_write_without_response_cb (from zephyr>subsys>bluetooth...
I measured the impedance using a VNA on the J1 socket of the nRF54L15-DK RF: With the RF configured for receive at 78.6 + J7.8, RF transmit continuous carrier at -40dBm: 23...
Hi Nordic support:
Our product used nRF9151 modem. During production, we encountered an issue with approximately 0.1% probability on the nRF9151: It's firmware lost or corruption...
I used the timeslot function of the nrf52832, but when I called the radio to send data, I found that the signal strength was very weak, much lower than that of BLE. This resulted...
I am using nRF9160 DK with nRF Connect SDK v2.9 and the LwM2M client sample ( /samples/cellular/lwm2m_client/ ) , converted from PSK to X.509 certificates .
The device connects...
In the software development for the nRF52832, the SEGGER_RTT_printf() function is called throughout the code for debugging and problem analysis.
Would there be any particular...
Can I copy the ESB code from SDK v3.3.0-preview3 into SDK v2.9.0, and then get the functionality in esb_ptx_ble & esb_prx_ble?
Is there any way to achieve it quickly?
