Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi team,
I am using nrf52840 Development Kit,sdk 15.2,Keil IDE
I am using MPU6050 sensor.For that,I used nrf5_MPU_examples_master file.
I have integrated ble_mpu_sensor...
Hi,
i was looking for nrfjprog command line tool on nordic website. But this tool not available to download. Is this tool got replaced?
If yes, then which is replaced...
Everybody is good !
I want to know whether BLE can broadcast, connect and communicate normally when nrf52832 communicates with nrf24L01.
The data manual says that it supports...
Hi,
After long time again started working on nordic controller's. Previously my pc was properly configured for NRF5x environment which includes gcc and flahser.
Recently...
The pin connected to lis2dh12's int pin consumes about 300 uA.
But the pin I used as button,also enabled int function , works good.
The pin I used as wake-up is in input...
In order to establish a wireless connection from my pca10056 developing card and a second nRF52840 SoC module using example CLI commands, and then being able to check/set...
Hi,
I have few queries regarding the internal regulators of nRF52840.
1) Is it mandatory to configure the internal LDO or DC/DC regulators of nRF52840 ?
2) If these...
Hi,
As mentioned in the Ch. 5 "nRF52840_DK_PB_v1.0.pdf" Section 5.3 in "high power mode the external supply should be connected to just the "VDDH" pins and "VDD" pins not...
I want to write to nRF52840 the example "ble_app_hrs_pca10056" from nRF5_SDK_15.2.0 by command line.
first I merge 3 hex file (bootloader, softdevice and app) with the command...
Hi,
I'm developing BLE 5.0 applications as a peripheral on nRF52832 under Windows, based both SDK14 and SDK15 (Softdevice S132).
I don't have any smartphone that supports...
Hi every body,
There is a problem with pwm driver example in demo3 part! after downloading, the board led is just on as it must, but after changing top_value there is no...
Hello everyone, I am planning to use the nrf52840 with the ECG sensor ads1298 (AFE for 8 channel ECG). The sensor interfaces via SPI to nRF52840. Has anyone worked on ECG...
Hi all,
I am working on nRF52832, nRF5_SDK_15.2.0, nrf5SDKforMeshv300src, softdevice_6.1.0 and communicate with CAP1214 device.
When I erase all flash on nRF52832 and...
Hello all,
I am using nRF52832 IC, Segger ES as IDE, SDK 14.20 and SD v5.0
I have around 70 bytes of data to be sent to a smartphone. I am using nRFConnect app to check...
