Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi everybody, i want to read NFC tags and send them via BLE to iOS app. How can i do that? Can i work with nRF51822 and Elechouse NFC R/W ? www.elechouse.com/.../index.ph...
I'm using SDK 9, I flashed the softdevice 8.00
I compiled the project located in \SDK_9.0.0\examples\dfu\bootloader\pca10028\dual_bank_ble_s110\arm5_no_packs
I flashed...
Hey,
I am trying to use app_timers and nrf_delay_ms together but the system gets stuck almost everytime. I have the following code:
void timer_handler(void *p_context...
We have noticed an issue when using the UART on our nRF51822 (SoftDevice = S130, nRF51_SDK_9.0.0_2e23562). Our Nordic app waits for commands on the UART and processes these...
Hello Everyone
I am trying to configure the two GPIO in High Drive mode 5mA but after compiling the program it does not seems like congifured to High drive Mode because...
Hello, I am designing a system to transmit a mono or stereo audio signal over RF, a few hundred feet, then receive it and reconstruct the audio and listen to it on a speaker...
I am developing a HID keyboard with SDK v6.1, SD v7.3, IC revision 2.
The keyboard is already able to advertise (non-whitelist) and bond with iPhone, and connect/reconnect...
Hello
I want to optimize SPI com as fast I can do:
First I am using the fast spi data rate by SPI_FREQUENCY_FREQUENCY_M8 variable and I want to reduce at first the timing...
As far as i understood it supports 4.2 BLE because using it i'm able to see packets between nRF52 central and peripheral boards (HRM example). Is it so?
Question:
I am confused about who can do (or rather who usually does) whitelisting - the master or the peripheral device?
My findings so far:
I can't find a certain...
Hi,
I have written a windows 8.1 application to connect to my custom nrf51 device. It is used for configuration and is set up without requiring a password (I do not need...
I want to be able to transmit the on-board temperature and battery voltage over a beacon application. The application only needs to transmit periodically similar to an iBeacon...
Dear,
I'm now face problem on button interrupt.
I use 3 buttons for my system.
button 2, 3 is used for boot diagnostics. assigned as below.
bsp_event_to_button_action_assign...
I'm trying to lighten the leds using ble, my problem is that when I measure the current consumption when the leds command sent, it reaches to 5mA which is not suitable for...
