I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi , I flash periodic_sync_conn sample to A and B development boards, and periodic_adv_conn sample to C development board. Only A and C development boards work normally, but...
Hello. We are developing custom boards with the configuration of nrf5340 + nrf7002.
In the previous sta example, a build error occurs when the "Board Target" in "build configuration...
I have customed my own nrf54L15 board and it would run on button battery. I managed to measure the battery level through ADC, but I don't know how to use ADC with nrf54L15...
I've been working for months to try and figure out exactly how to get my application to bond the way I want it to.
I'm using nrf connect sdk 2.4.2 on an nrf52832. I used...
I recently received a nRF9151-DK and try running example "hello_dect".
Apart from setting the CARRIER in "Kconfig" to "1" i did no changes to the code.
Building and...
Hi,
We are facing issue with upgrading our devices using DFU library.
Despite using the latest version of the Nordic iOS DFU Library , the firmware update process exhibits...
Hi,
I know that the nRF52 Dongle should be able to use printk() to debug. I have used it with the Serial Terminal before and it was working.
However, when I program...
I have mistakenly disabled Software Debugger (SWD) and wrote the configuration back to the board. Ever since board can not
(1) Connect and get the configuration data using...
Previously, I successfully completed and performed OTA flashing, and I haven't made any changes to the DFU-related programs since then. However, recently, I have been unable...
Hi! We have tags based on nrf52840 and nrf52833 in the field, running against a central with a nrf840X dongle.
Recently we have had an inexplicable peak in 'Failed to Encrypt...
I want NRFX_SPIM_EXTENDED_ENABLED to be 0. but for some reason it is set to 1. from my current understanding I conclude that the if case here check weather each node with...
Hi
I used the nrf-esl-bluetooth-2.6-branch example to flash the 5340DK (AP) and 52840DK (Tag). I sent the command esl_c pawr update_pawr 9 0 , and then sent the command...
Im trying to clear NVS, it gets cleared but then causes device to reboot.
code in question is :
output halts after Erasing NVS flash memory (0x000f8000, size: 24576...
Hello,
we are developing our first predict with the Nrf52840 running with VDD at 1.8V(default option).
so far we have always programmed and debugged NRF52 devices using...
