hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
Device: NRF53
I'm trying to send 3 notify packets in a 15ms connection internal but I can send 2.
I'm using Nrf connect and Zephyr. is there a limit or a define...
I seem to be having weird issue upon initializing qwr module in my .cpp file
NRF_BLE_QWR_DEF(qwr);
Doing so results in a syntax error
#define NRF_BLE_QWR_DEF(_name...
I created a custom BLE service following this tutorial and I am able to connect to the BLE service and write data to it, but ideally, I want to send character bytes as opposed...
Hello,
we are using an nRF52833 for our application with the open serial uart bootloader and MBR programmed in it. What we would like to do is:
1) program the application...
Hi everyone, I'm trying to get the LIS2DH12 driver (SDK v15.0.0) to configure a LIS2DH12 sensor connected to my nRF52 Dev Kit. I've wired the chip up as follows (using the...
I set the publish address of client using function:
Unicast address of sever is 0x0003.
After setting publish address by this function, I check publish address from...
Hello community... I was able to compile the GPS sample and flash an actinius icarus (nRF9160) using the Actinius Programmer once and it said successful. However, checking...
NRF52833+SDK17:
I want to use the saadc to sample a DC brushed motor running current when pwm at rising edge, pwm driving the motor.
I can't understand the real meaning...
Hi, I've been working on SDK v1.6.1 and I just wanted to try the v1.7.0, however some functions on the power management have changed, in particularly:
int pm_device_state_set...
I am encountering a problem with programming an nRF52840 DK:
1. I've installed nRF Connect for Desktop version 3.7.1, nrfjprog version 10.14 and Segger JLinkARM.dll version...
Hi,
I'm using the CLI and have logging enabled. The only way I'm able to see my logging output is if I type "log enable info" at the CLI prompt.
Is there a way to enable...
Hi to every one,
i have some questions, I need to be able to update the device to the new firmware, update to the old version and update to the default firmware. for this...
I am connecting the nRF52 DK to an oscilloscope and on the LED pin for the dimming example on the server side. I am seeing jitter, the PWM duty cycle doing a slight shift...
