Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
as discussed in different issue on DevZone . We have discovered that send command freezes the program in the CoAP client sample. The Nordic employee Hakon has confirmed...
Hello,
This is related to a previous post , but now with new information and a more specific issue to resolve.
We have product in the field based on RF Digital's Simblee...
HI
I used nrf51822- EK board.
BLE HID MOUSE - SDK 8.0
`
How to send left button or right button data?
How to modify below method?
static void mouse_click_send...
Hi everyone,
I'm working on a custom bootloader for nrf52840-based board. The bootloader needs to support DFU from an external SPI Flash and also BLE. I was working on...
Hi everyone,
I am trying to use the nrfx_uarte driver. I did the following:
(a) setup driver
(b) setup the event handler
(c) finally tried to send some testing...
I noticed a lot of the early SDK's 11, 12, 13 examples that had the service changed characteristic enabled. I'm using SDK 16 and it seems that most examples don't enable the...
I'm building an LTE device that only needs the GPS, LTE, motion, and button.
I'm trying as the first step to disable all the sensors that are not needed so that I don't...
Hi Nordic When the BLE is connecting, the fs_event_handler hasn't any callback after doing nrf_fstorage_erase or nrf_fstorage_write.
It seems like the storage (nrf_fstorage_is_busy...
Hi,
I noticed that there were changes in some of the priorities in SDK config - these defines were changed from 7 to 6.
NRFX_CLOCK_CONFIG_IRQ_PRIORITY
NRFX_GPIOTE_CONFIG_IRQ_PRIORITY...
Hi Nordic Support,
I am currently developing an IoT application (battery powered, cellular device with a few sensors connected). I have spent the past year building the...
I've read a lot in different posts about this but still fails to wrap my head around this.
We have a device using GATT with a few services, each with a few characteristics...
I am investigating Bluetooth mesh examples, which you presented, and I faced with incomprehension with initialization of struct bt_mesh_elem . Can you explain the meaning...
Does Nordic have an examples for implementing symmetric encryption at the BLE application level? I'm trying to understand how best to start because the Bluetooth LE security...
I have a setup where nRF91 and nRF52 on nRF9160 DK have to exchange ASCII strings over UART. nRF91 runs Zephyr and nRF52 - nRF SDK for Mesh.
When nRF52 is unprovisioned...
We are using mesh SDK v3.2.0, nRF SDK 15.3, nRF52840 DK and SES as our IDE.
We had a mesh network with around 5 devices and after a while 2 of them just stopped sending...
