I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I've been struggling to track down excessive power consumption on a nRF9160 device and have found that, when all UART/Serial are de-selected/off, adding or commenting out...
I want to modify the asset tracker application, for that I copied the 'asset tracker' folder from 'ncs/v1.4.0/nrf/applications' to a folder outside the ncs directory. Then...
I am trying to add a characteristic and am getting error 7 (invalid param). I started out calling sd_ble_gatts_characteristic_add() directly but I realized that characteristic_add...
Problem:
I am trying send samples from SAADC to the NRFconnect app at 1kHz. I have built my application on the ble_app_uart__saadc_timer_driven__scan_mode example . I have...
Chip: nRF52832
SDK: 15.0.0
SoftDevice: S132 6.0.0
IDE: IAR EWARM 8.30
I have a peripheral-role application with __ICFEDIT_size_cstack__ = 0x800 (application call stack...
Hi Nordic:
I know mesh LPN can receive messages from it's friend node, that means when any other nodes send messages to LPN unicast address, LPN's friend node will buffer...
I have developed hardware utilizing an nRF52832 and am developing a bootloader for the system. I have had success following two tutorials: Getting started with Nordic's Secure...
Hi,
I'm trying to print a float over UART but I think the NRF implementation is faulty. I've tested not UART SDK example with the following changes, inserted at line 168...
I have a Thingy 91 and try to analyse the PSM and eDRX in asset tracker application. I use NCS 1.4.0 in this case.
In prj_thingy91_nrf9160ns.conf file I found the settings...
I have: nrf51822 bluetooth module, STlink V2, Keil, segger studio, nrf51 sdk and softdevice files.
I have achieved making the led blink at a ble peripheral device by nordic...
Hi,
I'm using nRF52840 with nRF5 SDK 16.0.0 and Mesh SDK 4.0.0.
I'm trying to add PB-GATT service to the ble_app_uart_coexist example. I set MESH_FEATURE_GATT_PROXY_ENABLED...
我正在执行ble_app_uart_c例程的功率测量，并且已经关闭了串行端口，这与打开串行端口时测量的波形不同。 我猜封闭的串口会影响扫描。
This is the waveform without closing the serial port
This is the waveform without serial port...
I add a compiler flag --wchar32 i n the Misc. Controls section of C/C++ to support character pointers with 32-bit width. But got errors as log attached. Any help is appreciated...
Hello guys,
I am a newbie with nrf52 and I am trying to debug ble_app_uart project under ble_peripheral directory. I do get download successful as shown in image below...
