Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
Is it possible to send entire array over ble?
Char *data100];
For (I=0, I<100, I++)
{
Data[i] =timestamp_data;
Ble_nus_data_send(&m_nus, &data,size of (data...
Hi,
I have a custom NRF52810 board in which i flashed modified code of low power ESB example and is working.
but when I flashed along with the bootloader, the application...
Hello,
We have a custom board with nrf52832. We have seen a problem during production. Our process is as follows (the below steps are ran in a script),
1. We recover...
I think the nRF connect SDK uses RTOS since it is based on Zephyr. Is the Bluetooth SDK using bare metal? What about the Bluetooth Mesh SDK?
Thank you for your time.
Hi there,
I'm currently working on getting a streaming application running which is supposed to sample some audio at 16kHz and send it (uncompressed) to a central device...
Getting these linker errors that I believe may have to do with upgrading an example from SDK 16 to 17... however I'm not finding anything useful in the release notes as far...
Hi, I am carrying out a project that tries to collect the information from a sensor (sporadic activation), process it, and send it by BLE to a receiver to activate a relay...
Hi,
i am begginer, using my nRF52832 DK with ble_app_uart as peripherial, which is connected to PC via J-link (usb cable). I want is to establish serial communication between...
Hi,
in DFU error occurred and showing as [DFU] Remote DFU error: Insufficient Resources in the log.
Chip Used NRF52810
package size is 53.8 KB
is there any restriction...
Hi,
I just got a ppk2 and I am not sure which wire needs to be connected to where.
I am going to use this to measure current consumption but I've used only extarnal DUT...
Hi all,
I'm starting a project with a nRF52840, and start protoyping with pca10056 board.
I started with compiling ble_app_blinky example app, with armgcc.
I can compile...
My nRF52 device has a connection opened in peripheral mode and in some cases I want to close the connection with reason code "power off", i.e. call sd_ble_gap_disconnect with...
Hi,
I'm reading through the documentation on using the SAADC with the NRF52 kits. The examples are using PPI to manage the SAADC and allow it to sample locationally in...
