I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Dear Team. There is a bug in the SDK starting from version 2.9.0 regarding the linkage of libraries. Indeed, I have a CMakeLists.txt file that works perfectly and correctly...
Hello,
I have a custom hardware around the nrf52820, and I simply can't make it to run the basic hello_world and blinky samples.
I'm compiling the samples using nrf52833dk_nrf52820...
Hi,
I've just migrated my project from NCS 2.6.1 to 2.9.0 and I'm having some problems with the UART.
I'm using the nRF52833 DK to communicate with another device and...
Hello,
I want to port blinky example to 52805.
I wrote this dts file:
I added " CONFIG_DEBUG =y" to prj.cong.
I launch debug but main function is never reached...
I discovered weird modem behavior when testing my application with a weak or undetectable signal. Mine testing was as follows:
modem connected to the network
communication...
Can the npm1300 be set up so multiple interrupts trigger the same line, and then the host can determine what the cause is?
Or does each interrupt need a 1:1 correspondence...
We are developing a device that uses BLE, 4 contacts (buttons), a piezo connected via PWM and a realtime clock (RV3028). It also stores event data on an external flash using...
My application communicates via UDP and all communication is initiated from the device. Before packet transmission, network registration status is checked (CEREG) and sendto...
I boot AOK after I do a west flash --erase. But after that, when I try "west debug," I run into this:
*** Booting nRF Connect SDK v2.9.0-2e7ce73f5faf *** *** Using Zephyr...
I am trying to follow the first lesson of https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals
But I have several problems and I can not find out how to fix...
Hello
I am playing with the mesh dfu and the distributor application on nRF52840 DK board
I load the image I want to distribute using mcumgr application on a Raspberry...
Hello
According to Enhanced ShockBurst (ESB) documentation , to stop the ESB module you need to call esb_disable(), but it also says that you need to check if the module...
Hello,
We are considering to develop an appliance based on the nRF5340 AUDIO DK.
The nRF5340 AUDIO DK contains the VM3011-U1microphone that is absolute on the market....
Hello,
We’re testing the nRF9160 GNSS performance on our custom PCB and have noticed that, even with A-GPS, the first fix after powering on the device takes significantly...
I am having problems flashing my custom board with a nrf5340 chip. Sometimes it works, sometimes it does not, but more often than not it doesn't work and I cannot figure out...
