I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I'm trying to interface bno055 with nrf52 dk (PCA10040). I had written the relevant code for the nrf52 dk and added the same to ble_app_uart code and simple uart code. I'm...
Dear colleagues,
I am trying to erase / program the custom board ( with nRF52832 SoC installed) using nRF52-DK. The setup looks like that:
nRF52-DK Custom / External...
Hello Everyone,
I wants Real Time Clock examples in nRF51 board. Like following link which is implemented on embed microcontroller for nRf51 board.
can any one help...
Hello,
I want to discuss the following code with you:
www.dropbox.com/.../AABddGcZagoqWHnJqfPrpbm9a
In the main file there are init functions for uart and twi and...
Hello,
I am using pca10028 and sdk 12.2. I want to scan the nearby ble devices and want to display the mac address using uart. So which code should I refer or which thread...
I am doing some custom work, and have discovered an odd bug, that I can not seem to figure out.
On the tx radio, I am transmitting a BLE ADV packet with the first 3 bytes...
On nRF52, I see that 100 kHz gives a SCL period of 10 us which is correct but for 250 kHz, I get 8 us instead of expected 4 us. Similarly, for 400 kHz I only see 5 us instead...
I have a case where a module that can perform bit clears in the UICR needs to execute while a Soft Device is present and enabled.
I am aware that any direct flash access...
Hi Nordic and fellow developers,
I have been working on upgrading the nRF51822 QFAA s110 and upgrading the soft device to work as s130 for its (simultaneous Central/Peripheral...
Hello!
I'm trying to read data off of a commercial blood pressure monitor (Qardio arm) using an nrf51822 with the nrf51 SDK v10.0.0 as the central role (s120). I am able...
Hi,
we are using nRF52832 and running into memory issues as we add functionality.
It would be great if the '40 was available as a drop in replacement in WLCSP package...
Hello.
I want RSSI check. so added source code as below.
test_rssi_start = sd_ble_gap_rssi_start(m_conn_handle,BLE_GAP_RSSI_THRESHOLD_INVALID,0x00);
if(test_rssi_start...
Hi all,
Is possible using NFC to send variable message? I want to send a counter event (data I got via BLE) to the NFC module.
Using the example I was not able to do...
Hey,
I'm just wondering how to add a UUID to the blinky example peripheral?
I want something like the heart rate sensor where its advertising BLE_Heart_rate_sensor.
I...
We have recently migrated from a custom board based on the nrf51 to a new board with the nrf52832. Our nrf51 board used to run at 6-8 uA when it was just sitting there advertising...
