I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I am working for the first time with NRF52832 flash data write. I have (ANT + BLE) application and and I basically want to save the data in ROM in order to keep it saved...
Designing a custom pcb, we have a few questions, and maybe you could help a little bit.
On this Nordic design ,before proceeding to layouts :
Can I skip pins 45/46...
So im trying to create a generic library to test any Bluetooth device. So far i can connect to the device but since i dont know what are the services and UUID available im...
Tried Flasher Portable Stand-Alone Mode with J-Flash 6.14 as following:
Create .jflash Project for nRF51822-QFAA
Open Data .Hex File
From J-Flash, select Target...
Hi,
This is obviously not the first question about this, but I still haven't found the answer I need here...
I would like to make a kind of serial to BLE gateway on...
Hello Nordic Community.
I'm having issues trying to control a simple RGB LED circuit with the NRF52. I have set up 2 timers and PWM instances Red and Green on PWM1 and...
I am performing automated testing on my device using an xml file that I have written. My xml contains a disconnect command. I observed that NRF connect reconnects to my device...
Hello,
After looking for pin mapping for TRACECLK and TRACEDATA[*] for nrf52840 I've seen 3 different mappings:
P0.07, P1.00, P0.11, P0.12, P1.09 in infocenter.nordicsemi...
Hi
I need to send as much data as it is possible in the advertisrment payload. Whem weset the devicename there are other fields that are automatically added to the payload...
I'm having issues executing any Zephyr project on a breadboard connected to a ISP1302. It works fine on the nRF51-DK but anything I try a final hardware nothing happens. Tried...
Hello,
I am using nrf52832 with PCA10036 V1.1.0. Soft device code is s132. I would like to know whether it will support Bluetooth 5.
I have downloaded nrf52 sdk13.0...
Hi, Dear Expert:
I am an Electronic Engineer. We used nRF51422 or nRF51822 at our products, but found the products was easily reset when did +/-1KV contact ESD testing...
now I used sample code of radio
change NRF_RADIO->MODE = (RADIO_MODE_MODE_Nrf_2Mbit << RADIO_MODE_MODE_Pos)；
In transmitter code , I change
while (true...
Story Short: When trying to run the ble_app_uart example on a custom board with a nRF51822QFAAH0 chip, the code faults and resets at the point in tries to call sd_softdevice_enable...
