Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
I have done BLE tutorials [BLE Advertising, Ble Services and BLE Characteristics]
With my NRF51-DK was working perfectly the example of BLE Characteristics (with...
Hi,
I designed a pcb using nrf51 chip with some sensors,
this pcb should read ,every minutes, all values from sensors and saves them into the flash memory beside that...
Dear
Now, I need make one nrf52832 board as USB Dongle, it can be HID device by checked from PC.
And, nrf52832 should support esb protocol, now for esb, I know something...
hai
i was started a bluetooth based project. So i have started with a blend micro.But the range of communication was very short.So i have chosen ble nano with TX power...
Hi
I am calculating the power consumption using
devzone.nordicsemi.com/.../
But there is some point that I don't understand.
When the BLE event type is "Peripheral...
Hello,
the past week I am trying to make the bootloader_secure example work for a custom hardware with no luck. This whole procedure give birth however to several questions...
Hi
I am currently working on a BLE based hardware but I am a little confused about the terms such as service, characteristics... etc.
Let's say, I would like to control...
Hi,
I am using the following function to read the content of a register:
static ret_code_t read_reg(uint8_t slave_address, uint8_t register_address, uint8_t *value)...
Hi,
Could you please help me identify the file and function name that is used by the S130 softdevice to start HF clock automatically for ble advertising? I can see that Clock...
Hello again,
I'm working with the ble_app_hrs example application with DFU app support. I'm following the DFU procedure and I've reached the point where I actually start...
Hi everyone,
My idea is:
I have several nrf51822 ble devices and I want to connect them simultaneously one by one with gateway over IOT. I am using bluz gateway shield...
hi all,
I use nRF52 SDK11 with ble_app_beacon example.And write some code in main().
uint8_t buf_data[32];
unsigned char c_data[] = {"abcd"};
//unsigned char c_data...
When debugging my application, I'm finding that gdb blocks at app_scheduler.c:253 like this:
(gdb) bt full
#0 0xfffffffe in ?? ()
No symbol table info available.
#1...
I'm using SDK 12.1.0, gcc, nRF51822, no SD init'ed or enabled at the time this code is running. I need to retain the values of a bunch of variables across a sys off.
Here...
