Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi,
I am developing a product for the 433MHz band. Due to the space constraints I had cut the ground plane to very small and also had to rearrange the components away from...
Hello everyone,
This image was copy from "infocenter.nordicsemi.com".
I'm trying nRF51-DK (IoT SDK) with Coap server , (raspberry pi with Coap client by python example...
Hi,
we are using RTC2 with APP_IRQ_PRIORITY_LOWEST. But the code hanged inside the interrupt handler. when we did step through debug, we came to know that in nrf_drv_common...
In nrf52_SDK/examples/peripherals/rtc we tried adding the UART prints and verified. It was working fine for RTC0 but fails to do for RTC1. Could you please give any hint on...
Hello together..
i have a problem with the nRF51 DK.
I tried a little bit with this DEVkit i.e. copy the blinky example to the JLINK storage.
This works fine.
Regarding...
Hello,
I am developing a new product using S130 on nRF51822(QFAC). My product use LCD as spi interface and ADXL345 sensor as i2c interface, also test it, works well without...
Hi all:
To saving power I implement the function to read data after interrupt is triggered..
below are my codes..
My expectation is..
Let CPU enter idle mode to wait...
I am trying to set up a GPIO interrupt, and found that whenever Button 1 is pressed, if Button 1 or 2 is pressed later, the app will reset. This is even if there is any other...
Hi.
I want to make a device which can connect each others and communicate with NUS.
I need not to use any other service without NUS.
I made nus_c service which is a central...
Hi
I can't seem to find this in the datasheets, what is the active current consumption of the nRF52832 chip, I'm interested in the maximum expected current consumption...
Hi!
I want to connect a nrf51 dk with a beacon and I'm using the UUID to make the connection. In the beacon code I define the UUID in this way:
ble_uuid_t adv_uuids...
I use nrf52832 with softdevice s132_nrf52_1.0.0-3.alpha for a ble application on own pcb.
first I'm not sur of adresse to use for iROM and iRAM areas. I've this parameters...
//Hi Everyone!
//I am programming a nRF52832 through the SDW interface and am having trouble answering some questions.
//So, first off is simply checking my understanding...
I have a recent dev board and am using SDK11 with gcc.
I can build and flash OK
The blinky sketch runs
However, when I load up examples/ble_peripheral/ble_app_proximity...
We bought the Beacon Kit from Nordic. I'm trying to use the firmware code on a similiar beacon board based on same Nordic Nrf51822. The board has same button and led pins...
