hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi, I have followed the nRF Connect SDK Fundamentals and BLE Fundamental courses and come to Lesson 6 Bluetooth LE sniffer. Everything has worked until this but now I get...
Hi,
In nRF52811-CAA chip, which pins are allocated to ADC inputs. In Table 122 of datasheet which shows pinout for WLCSP package, it just mentions AIN1, AIN2, and AIN3....
Hi,
I am facing an issue while flashing the code using an external debugger. I want to flash an LED blink code on the I/O shield " Raytac MDBT53V-P1M. " For this, I am using...
Latest 2.7.0 toolchain.
nrf5340DK board, light_bulb example.
I am using our own smartphone to perform up to AddNOC and ThreadNetworkSetup.
Then the control is transferred...
Hi, I would like to write a log to an SD card but I am completely unable to even connect to it using SPI in Zephyr/nRF Connect SDK. There seems to be some mismatch between...
I am working in NCS v2.7.0 for nRF52833 DevKits, and trying to set up a secure BLE connection to allow remote control of the device over GATT.
My devices are headless IOT...
Hi All, I have a 5340dk and it got bricked for no reason, last night I was able to flash and debug my program. But when I tried this morning, device is behaving unexpectedly...
Hello !
You have DTM test in nRF5_SDK_17.1.0 and in nRF Connect SDK.
I have used SDK test some years ago and it looks more simple if we compare it with new environment...
Hello,
I am working with the nRF9160 to communicate via DTLS. It works, but managing certificates is a bit of a problem. I am using the AT%CMNG command.
First, certificates...
When running example code which involves BLE on nRF52840-based boards, the devices (which have assigned names in the example code) don't show up on the iOS nRF Connect scanner...
Hello,
I am using nRF Connect v2.6.0 and nrf52832 for product development.
I have implemented MCUmgr callbacks to check the DFU status, as shown in the code snippet...
I need to move everything off of UART0 so I can use it for my touchscreen
On a previous post I was told I could move everything to RTT in the overlay, but when I try to...
