I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Dear All,
I would like to know information about QDID for nRF5 SDK for Mesh v4.2.0, we are developing costumed equipment using NRF52833 and we need to start the process...
Dear Nordic support team.
Our product nearly complete Rnd stage.
We face only one thing relate to "Cannot reconnect after unpair device with smart phone".
debug wit...
How can i give command from android device to ble board to get the percentage, temperature, or reset or shutdown the device with the help of receiving command from android...
I'm trying to register the SIM card of the 9160 DK at nRF Connect website,
but the website is always showing "still working..." for more than 15 minutes.
Do you have a...
Hello,
I am experimenting with setting up a network via grouping in the following manner.
Bulb_1 will be put into identification mode, and Switch_1 will detect Bulb_1...
Hello,
I am trying to send gps data using MQTT protocol. For this purpose I wanted to combine MQTT simple example with the GPS example. I added all the methods/dependencies...
Hello,
I started to work witn NRF Connect SDK with nrf52840-dk? I mapped lots of peripherals to NRF Connect SDK. There are no problems. However, I try to map nrf_fstorage...
Hello
I am testing out a blinky FreeRTOS example that's a part of the SDK and would like to use SystemView to visualize context switching and tasks. Are there any steps...
Hello,
We're using a BLE connection configured with a 15ms connection interval, and a radio event notification configured to fire 800us prior to a radio event. I'd like...
Hi,
I trying to create a blank Zephyr project for NRF52 and want to use SES. But I could only open pre-existing samples and there's no way to create a blank project.
Appreciate...
I want to create server and client in nrf9160 not through LTE. only transmit on locally in nrf9160
//prj.conf # enable libs CONFIG_NEWLIB_LIBC=y CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi support team,
In PS, it stated the sensitivities for ideal BLE transmitter, I would like to know:
o Sensitivity at 1M PHY DLE 255 octets , Dirty Transmitter on
o...
Hi,
In the documentation [1] for 802.11.4 for nrf52-sdk it is mentioned that the documentation is for the nrf52840 soc only. Where can I find documentation regarding 802...
