hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,
In order to measure the RF power, I measured the RF power by radiating inside the RF shield box.
But there is something strange.
The position between the device...
Hi ,
I want to develop the firmware to read the nfc tag and read the sensor data send to the application via BLE I have read many post regarding nfc . Let me explain what...
Hi,
I am working on temp. sensor with nrf52832 dev kit for firmware testing and development and also using nrf52810 for product testing.
in my code, I merged twi communication...
hi,
I want to develop a project based on ble beacon mode and ble app hts code.
and I am using nrf52810. so will it work if I merge both codes and use for this project...
I know that nrf_cal_set_time() from the nrf calendar example is NOT meant to be called on a regular basis / should only be called to update the time being kept locally to...
Hi,
We are looking for a guideline to trigger GPIO and SAADC sampling at the same time.
Our purpose is to sample every 20 m
Hi,
We are looking for a guideline...
Hi, We have a DFU OTA process that was functional, but updating our softdevice to s113 7.2.0 has left us with a problem - since the softdevice does not exist in the nrfutil...
Hello.
I am doing a small project where nrf52 reads data from a BME280 temperature sensor via SPI and sends it using ESB.
I have no experience with radio, so I use a ready...
I would like to use the NRF24L01+ from a 3v coin cell, but interface it over SPI with a 1.8v-powered microcontroller. Assuming the uC is tolerant of the NRF SPI outputs, I...
We have a application where data transfers happen through a mechanism where the external client does a write-without-response to send in a command. The response to the command...
I am busy with my first BLE project , programming a custom service for both pheripheral and central role. I have already finished the pheripheral service, using a custom service...
There are other GPS modules on the market which can give information like "the device is within 10 meters of the given coordinates". Is there a way to either get this information...
Hello,
i am using AES CCM encryption available in nrf52832,
my data which need to be encrypt is same every time. data will encrypt and 4 byte will add at the end of...
Hi all,
I am working on a project with the nrf52832 and I am using softdevice S132 6.1.1. After creating my desired flash layout (with some help on this forum, thanks!)...
Dear,
I am using NRF52840 and nRF5_SDK_17.0.0_9d13099 and SES development tool.
And also, I am testing SPI master with p0.29/30,31 and P0.26.
but when I do "nrf_drv_spi_init...
