Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello,
I'm using a NRF52832 QFAA connected to a Quectel modem through UART. We're using UARTSerial from Mbed OS 5.
We've produced 12 custom boards where on 2 of them the...
Hello,
I'm working on adding an HTS service to an existing device (nRF52832), and running into a problem that can be reproduced on PCA10040 and S132 5.0
When my code is...
I modified the firmware of our control unit to allow BLE communication. Now It communicates with an ANDROID APP. The chip used is nRF24L01+, It send and get only Non-Connectable...
Hello,
I'm trying out the HID Keyboard example (sdk 16.0.0, s132) and was able to pair once to my phone. Now I can't pair to any device. The following pop-up window appears...
I'm running SDK 14.2 using FreeRTOS on a nrf52832.
When I increase NRF_SDH_BLE_GATT_MAX_MTU_SIZE to 158, the system ends up in Hard Fault.
Anyone have suggestions on...
Hello,
I am using an nRF52 to transfer 20 bytes (through notifications) to a raspberry pi (with bluetooth dongle). I've been experiencing some weird connection times: I...
Hi
I have 1 PCA10040 dev kit and 1 Raspberry Pi 3.
If I connect NRF dongle to Raspberry Pi will Raspberry Pi act as mesh-node ?
All I want to do is send data from PCA10040...
Hello,
nRF52840 is having the inbulit RTC for keeping the time.
Should i need to use external RTC with coin battery for even after power off the BLE nRF52840.
PLease...
Hi!
We're considering implementing some security measurements into our devices, and so naturally we've started to investigate CryptoCell and other Backends supported by...
Hello,
I recently updated nRF Connect to version 3.4.0 (Bluetooth Low Energy). I'm observing, that the tool is not able to reconnect to a peripheral that was previous bonded...
Hi Nordic Experts,
I use nRF52832 for a custom board, I use GPIO P0.17 and P0.18 for controlling NMOS switch, for buzzer and vibration motor, and the frequency is controlled...
So I seem to be having trouble interfacing with nrfl2401. To initially test the chip, I sent `0xFF` to be able to read off the status register but when I do, I get `0x1C`...
Hello Nordic Team,
We are working on a BLE project with RSL10 board from OnSemi. We need a BLE sniffer to capture and analyze the BLE packets in the air for debugging purposes...
