I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi Nordic Pros,
I have a nrf52840 board, and I tried to connect it to my pc. It dosen't show up as "JLink" or "BOOTLOADER".
Inside Segger Embedded Studio, I tried to connect...
Hi, anyone call tell What is the acceptance rate of nrf52 series scanning
I'm used zephyr ble mesh example, One node sends, one node accepts, and the broadcast packet sent...
Hello,
When i build a project to the nRF9160 DK, the terminal shows output of the program. Everything works.
When downloading the merged.hex file to thingy91, then...
Hello everyone,
We are 4 students, who are developing a BLE mesh network to send data from a CANNBUS-simulator to a desktop. We have chosen to use the nrf52840 chip to set...
Hello,
I am using nrf52832 with SDK 16, I want to change advertising packet flags from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE(0x05) to 0x04 during run time how can...
Hi, Im developing an ac dimmer with zero crossing on mesh, but it flickers at low dimming levels, I even used the scheduler for the ble stack but it didnt help, what would...
hi, i am using nrf 52840 dongle , is there any support of AT commands to communicate with dongle .i want to communicate without using ui only by sending commands. if not any...
Hey Nordic Team!
My requirement:-
Sensor data----------------------------->nrf52832------------------------------>Raspberry pi 3 (via blue tooth)
Is it possible...
We are working on external RTC MCP7940(i2c) interfaced with nrf52840. Please check if drivers of the same for nrf52/51 are available or any implementation of CLOCK using MCP7940...
Hi,
I tried to add 3 characteristics and 1 gatt service to my NRF52810 using with development board with 10040e (I am using gcc compiler). Then I got a error which is saying...
we are considering using .005" thick stainless steel to provide better bridging effect across the opening on the board for the battery. This will provide more strength to...
Hi
I am trying to use an antenna switching board for AoA direction finding. I know that the RADIO controls 8 PSEL.DFEGPIO pins to control switching antenna.
1. Could...
Hi,
We want to use the NRF52810 without radio and we don't want to put the external oscillator to reduce the PCB size
I would like to know if necessary to have the external...
Hi,
Some time i could not put break points inside main for sample projects provided for nRF91, i tried clean build, erasing the flash 'nrfjprog -e' and evn enable the configuration...
We would like to use a Dongle based on the nRF52840 as a BLE Central communication via NUS to our product. The example in the nRF Connect Desktop does just wat we need on...
