Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi all,
I am using the latest Mesh SDK (3.2.0) and SDK (15.3.0) in an nRF52840 SoC.
I developed a message model to send 32 bytes payloads (which I assume would require...
Our BLE peripheral uses a custom GATT service similar to the NUS (Nordic UART service) used in the SDK example app_ble_uart. The peripheral receives data on the UART peripheral...
We are trying the Asset_Tracker application in the ncs\nrf\applications folder of nrf playground on Git.
We end up with the state; "lte_lc.parse_nw_reg_status: Network registration...
Hello,
I am searching for a provisioning API for the nrf52832 to develop an application for Android and IOS. My preference is one that already can work with Googles flutter...
hello:
our hardware engineer had designed PCB,it can't reach more than 100m..howerer the nrf52840 DK can reach 300 or more meter.
so is there any people can support some...
When using nrfutil to generate a DFU settings page (with backup page) of settings version 2, the .hex-file generated by nrfutil is not word-aligned, i.e. the number of bytes...
I noticed that as of SDK v16 a required component to use the Soft Device is nrf_section_iter which is located in the directory "\libraries\experimental_section_vars". Is this...
Hello,
The product specification for the nRF52832 only shows 3.0V performance. What is the performance in parameters such as Tx power, Rx sensitivity, maximum MCU clocking...
Hi,
I'm currently developing firmware in the Arduino environment using a dev board (Adafruit Feather nRF52840). Once I complete development, how do I transition the firmware...
Hi, I am developing the application in nRF52832 with SDK_16 in SES.
I have a problem with DFU
I need to run the application and DFU has to be activate only if the mobile...
Hello everyone
I'm using NRF MESH4.0, I have add simple_on_off model to experimental_dimming example,and it works .
My question is : MESH PROFILE V1.0 have mentioned bound...
Hello, i am trying to adapt DFU in the Light switch Proxy server example, however in midle the process of receive the DFU packets i got this error: Abort event. packet loss...
Has anyone (tried to) simultaneously use the same QSPI Flash memory directly from an nRF52840 program and as a USB block device?
We have both functions running in the same...
