I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I need to save energy for my ble application. So I turned off the sensor when there was no ble connection. A ble connection is a condition for me to turn on the sensor, but...
How exactly are the UART pins selected for the nRF9160? I've searched and am unable to find a file to configure pins. I need to change to pins from the development board to...
Hi,
I'm working with the SAADC on an NRF52832. I'm using the SAADC driver from SDK15.2.
I have a problem with the calibration routine because it's generating DONE events...
Hello,
I am developing an application on the 52840 and so far find the SDK documentation quite confusing and somewhat contradictory. I need to write a simple TWI (I2c) master...
Hi, I’m located in Liège, BELGIUM.
Using the nRF9160DK, an orange SIM card, MODEM firmware mfw_nrf9160_0.7.0-15.alpha I managed to make run some sample code:
mqtt_simple...
Hi. I'm using nRF52832, SDK13.0.0.
The roll is peripheral.
And I'm using Oberon to use ECDH.
I think you have the result or document for random generator's performance...
The nRF9160 DK I'm working on does not seem to be able to connect to nRF Cloud after following the tutorial:
https://www.nordicsemi.com/Software-and-Tools/Development-Kits...
Apologies, I accidentally closed and opened my previous ticket: https://devzone.nordicsemi.com/f/nordic-q-a/53073/unable-to-add-lte-device-on-nrf-cloud , can I check that...
The new SDK has no documentation on this functionality: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v12.0.0%2Fgroup__ble__radio__notification...
Where to get this RaspPi_OT_Border_Router_Demo_v3.1.0-1.alpha.img file.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v2.0.0%2Findex...
Hello
I need urgent help. From days I have been stuck exploring NRF SDK 15.0 to do a simple task.
I am using an NRF DK board PCA10040. After going through peripheral drivers...
Hi,
I am working with central and peripheral uart example and facing with connection problem between two boards.After debugging at the central side i am getting error in...
Dear Sir/Madam,
We have a customer to develop a product based on nRF51422 and then they passed their product for pre-registration test.
They used DTM interface to connect...
Hello
I have nRF52832 custom board and have BME280 sensor connected to I2C/TWI
Whatever I do I get same reading (for 3 different sensors)
I'm constantly reading same...
Hello, I would like to use nRF24AP2 in a SPI bus with an accelerometer (a slave peripheral). I need that the host works as master with accelerometer. But in this way we will...
