Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello, we have been using a nRF51822 8-pin RF module for a while now for various products, the pinout is as follows: power, P0.00, P0.01, P0.09, P0.11, SWDIO, SWDCLK, ground...
Hi I try to implement DFU to our application using Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0 When I use the DFU-Example everything works fine. I then implemented the DFU-code from...
Hi there, I have a custom board with nRF52840 and i am transferring fairly large amounts of data via uarte. I am also using my own driver. For some reason the attached device...
Hi,
I am Using NRF52840-DK Board. We are trying to transmit multiple data using NRFx_SPIM Example. for single reg read it is working fine.
please check below code is...
Hi,
I have certain doubts regarding simple message model .
1. Why simple_message_client_init or simple_message_server_init is never used? Don't we need this function to...
Hello,
I try to control led light of the thingy52 throw a MIT app inventor application.
I use the UUID : ef680300-9b35-4933-9b10-52ffa9740042
and thr characterixtic...
Page 362 of nRF52840 product specification version 1.0 March 18 shows A in 5 bits. The max entry is 0x0D (4 bits) and there has to be room for 8 entries in 32 bits. Hence...
hello, is there any way to generate DFU package without using command line. i am using segger embedded studio can directly generate dfu package in segger embedded studio please...
What is the wake time for module if i put module in system off mode in following cases .
case 1: Module will wake up by GPIO signalling
case 2: Module will wake up by...
Hello,
I need more details on DFU mode entering topic. I understand how to configure DFU to enter the bootloading mode on button press event but have dilemma about using...
I’m doing a project using NRF51822. We use P0.06 pin for PWM out while reading ADC from P0.01 P0.02 P0.03 & P0.04 .
As my experiment, when I’ve used P0.01 P0.02 P0.03 &...
Hello everyone, I was wondering if we could run IPSP over 2 BLE-supported nordic kits and ping one from another without using a BLE-Enabled router, like connecting them together...
Good morning everyone,
I am writing a custom protocol using the RADIO module and I am having a hard time understanding the address organization.....
My protocol supports...
Hi,
I want to interface an analog front-end Device through NRF52840-DK board Using SPI Interface . I want waveforms to be as Below:
which driver I suppose to use is...