Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
I need to understand how a multi-link configuration can achieve real-time transmission - its all about latency.
The Application
In my nRF52840 application I have several...
Hello,
I am using a custom bootloader. The bootloader does not contain dfu, it will just check the new image, program the new image, then jump to it.
I cannot jump to...
Hi,
I want my characteristic to have a different UUID than its service on my server:
I followed the leads from the post below:
https://devzone.nordicsemi.com/f...
Hi there
I was following all the steps on Building the mesh stack and examples , Building with SEGGER Embedded Studio and nRF5 SDK for Mesh Segger Embedded Studio first...
Hello
My understanding is that the only way a mobile phone can communicate with a mesh network is through the GATT bearer..
Im trying to figure out why its not possible...
Im using two nrf51822 as severs and one nrf52DK as a client in mesh light-switch examples. So i need to implement mesh dfu on server side( on nrf51822) . How to do this ....
Dear Support,
Installed the new Mesh SDK v2.1.0 and tried to build the sample solutions with SES.
Unfortunately I am always getting the following error:
build/serial_nrf52832_xxAA_s132_6...
I would like to use both UARTs.
I'm trying to run the given example with SDK patch from https://devzone.nordicsemi.com/f/nordic-q-a/25173/nrf52840-uart1-not-working-in-sdk...
Goodmornig,
I can't compiling the example project ! Do you knows the reason ?
Error ( imagw1 ): C:\Users\utente\Desktop\pc-nrfconnect-rssi-master\fw\src\rssi_uart\sdk...
Hello everyone, I'm trying to run my nrf51 with ADS1298 using SPI. nrf51 is master and ADS1298 is slave.
I configured SPI as
const nrf_drv_spi_config_t spi_config =...
Hi,
I'm trying to implement GPIOs in Mesh 2.0 light switch example and I'm using SDK 15.0. I'm getting undefined reference errors and I know that I have to add legacy GPIOTE...
Hello guys.
I'm new with nodic nRF52 SDK and I tried to enable debug by setting 1 on "NRF_LOG_ENABLED" in sdk_config.h, but nothing happens in com port criated by Jtag...
Custom app running on a nRF52 devboard. Serial port runs when I use the debugger and continues after I exit the debugger, but does not run from a cold start.
using the...
Hi,
In nRF5 SDK v12.3, the members of nrf_ecb_hal_data_block_t are pointers to non-const data. I was wondering if these indeed need to be non-const for the Softdevice S132...
