Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I'm beginner in the bluetooth environment so I don't understand everything in it.
For my project, I need to develop connection betweeen a BL652 and a smatphone.
In a first...
Hi,
For both (nRF52840 / nRF52832 ), with SDK version nRF5_SDK_15.3.0_59ac345
I am using Secure_Bootloader in the eample folder:
nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral...
I found an issue when using CONFIG_AZURE_IOT_HUB_DEVICE_ID_APP to set the Azure Device ID.
Around line 88 of azure_iot_hub.c the "user_name" structure is set using the...
Hi,
Is it true to say you have two modem firmware streams: 1.1.X and 1.2.X? Are these two kept in sync in terms of GNSS improvements? I notice the 1.2.2 release notes mention...
Hello,
I want to measure current consumption of nRF9160 of the Thingy 91 with the Asset Tracker application in PSM mode without GPS. For that, I added to the function modem_configure...
Hi,
Browsing the API I only saw Enhanced shockburst support. I need air compatibility to an old 250kBit plain Shockburst communication. No auto ACK and no auto retransmit...
I have run up the CLI example to test as we will require some command line interaction and why reinvent the wheel?
I run up the example with USB enabled and UART disabled...
Hello Nordic,
I try to establish communication between an ATmega328 based board an an Arduino Nano, so far without success. The goal is to improve a RF433 "Wire". 3 weeks...
Dear All, I am using the ADC to measure 3 voltages applied on different ADC inputs and 3 different channels. My ADC configuration looks like this: And this is how I am performing...
Hi,
I recently acquired the nRFgo starter kit and nRF2724 rev 2.1 and the nRFgo development kit. I have downloaded all of the supporting software that were found here...
I have the latest nRF Connect for Desktop.
After I install "nRF Connect SDK v1.4.99-dev1" in Toolchain Manager I don't have an "Open IDE" button.
I've tried uninstalling...
I am adding JLINK_MOITOR.c and JLINK_MONITOR_ISR_SES.s and add write
#if CONFIG_JLINK_MONITOR_ENABLED NVIC_SetPriority(DebugMonitor_IRQn, _PRIO_SD_LOW); #endif
at starting...
Hello everyone,
I'm trying to develop an application with BLE, using an example as a base.
The advertising is good, well configurated, I can edit manufacturer specific...
I am currently using Mesh SDK 4.2.0 and I could successfully write and read reliably from the flash using a second flash manager instance used in parallel with the flash manager...
