I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello everyone,
I'm a fresher of programming nRF52833. I'm working with Timer and I have some questions like this:
Can I use several timer in an application? I mean...
Hi, i have two boards with me i.e. nrf52840DK and nrf9160DK. I want to debug nrf52840DK using nrf9160DK, I don't want to use onboard jlink on nrf52840Dk, is it possible to...
Hi! I'm currently using
- board: nRF52840 DK
- SoftDevice v15
- ble_app_template example + midi (adding custom service and characteristic) -------------------------...
Hi,
I used SDK 16. softdevice: S140 v7.01. And set APP_USBD_VID and APP_USBD_PID to 0 at sdk_config.h
I follow this post of https://devzone.nordicsemi.com/f/nordic-q-a...
I'm trying to have nRF9160 DK communicate with an external accelerometer.
nRF9160 stop working at the function of i2c_reg_read_byte in the code below.
Does anybody give...
Dear fellow developers
I would like to integrate a smart lock ( danalock v3 ) with the alarm system, so that I can control the lock via the alarm system. The alarm provides...
Hello,
I have a few questions regarding power consumption of the BLE modules
With regards to the nRF52810:
The data sheet lists the following as specifications for...
Is there a quick way to disable MCU Boot on the Thingy91 Asset Tracker example? I need to use the button on the device to my applicaton, and it is neccecary that the user...
Dear Sirs, good afternoon
I am using a (PPK + nrf52840 DK) to measure current on an external device.
Is it necessary to cut the SB40/41 jumpers in this case?
Thanks...
Dear Nordic ：
I want FTMP (Fitness Machine Profile) to be supported in my product (A smart trainer uses NRF52832, called Gravat in Ant+ official website).
I find that...
I want to monitor the RTC count and generate an interrupt when a specific count is reached. And without stopping the RTC, I want to generate an interrupt again when the next...
Hi
We have the issue that GPS has no fix.(board: Thingy91 version: 1.0.2) I used the pre-compiled hex thingy91_ltem_dfu_2020-04-29_bc7ade8b.hex downloaded from Nordicsemi...
i want to connect Nordic thingy to a nrf 52840 soc with ble central example.
all i want to get is thingy environment service and get temperature and humidity values on...
