I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello,
I'm designing the electronic of the nRF9160. We use the ANT PIN (61) for frequencies in the range [700MHz; 2200MHz].
I'm wondering to add a band filter on the...
SDK16.0.0, S132v7.0.1, nRF52840
We call nrfx_uart_tx() from the main application (non-isr) context to initiate multi-byte data transfer from a queue we manage.
We also...
I am using guide provided at https://openthread.io/guides/border-router to create border router. I am using Ubuntu 18.04 on a PC. I tried same on RPi 4 too and seeing same...
Hi !
I'm setting up buttonless DFU on an nrf52832. I'm using SES on windows.
I found two ways of performing it, one in the forum and another in the infocenter.
The first...
Hi,
we have to program direct test mode software for our certification process of our device. What we did was: take the dtm example from Nordic SDK (v15.3.0) and programmed...
Hi everyone,
I am desing a low power BLE application using the nRF52840.
How do I restart the advertising after the APP_ADV_DURATION has been expired?
Thanks in advance...
Hi,
We developed a medical device based on the nRF9160 chip and we would like to do the EMC test for qualification. Does Nordic provide any examples or support for the firmware...
Hi Team,
I have flashed the given serial LTE Modem hex file(attached) into dev kit nRF9160 and tested TCP server mode.
I am facing issue with AT command: AT#XBIND=3442...
Hi,
I´m using nrf52833 on customized board with a sensor on it. I would like to send the data, collected from sensor ober ble to nrf connect app. I print the collected...
Hi community !
i'm working on nRF52840 DK. We'll put SoC into a device where we couldn't have access with a cable. So my questions are :
1) Does DFU example use OTA to...
Hi,
I have to use current time service and one other customized service in my project.I am able to advertise only one service i.e customized one.can you please let me know...
Hi,
I am working on the nrf52840 DK using "nRF5_SDK_16.0.0".
I tested out the example code for USBD Audio in "examples\peripheral\usbd_audio".
If I use the default values...
Hello. I evaluated the effect of temperature and humidity on BLE connection stability. I thought that the effect of humidity was higher than that of temperature, but the effect...
I'm trying to rate nrf52832 now. I'm using Keil uVision5 as my development environment.
I have written softdevice s132_nrf52_7.0.1 for the target.
I'm trying to set the...
Dear Sirs:
I use 52832, and there is 512KB internal flash.
So, I am wondering if I could have my own flash partition as below.
- Bootloader (w/ capability of firmware...
