hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi!
I use the peripheral blinky example from the sdk v15.0.0. I ave added some code so that the board is scanning for advertising messages aswell. Every thing works fine...
Hi,
I've just realized the project from
https://github.com/Martinsbl/nrf5-mpu-examples/tree/master/nrf52-mpu-easydma-using-gpiote-and-registers
And it is working quiet...
Hello everyone, I am trying to send and receive messages over UART using Teraterm, the PCA10059 dongle and the UART Android app.
I was following the directions found in...
When I was trying to update the modem firmware, it showed something like this...
Traceback (most recent call last): File "c:\python37\lib\runpy.py", line 193, in _run_module_as_main...
Hi,
I am working on increase data throughput between phone and nrf52832. I am using SDK 15.3.
I create a service and a notify characteristic. I am sending 20-byte packet...
I currently have a hobby product that reads sensors and turns on/off relays based on that sensor input. I've got an nRF52840 that sits on my sensors and relays, and I have...
Hi,
I am working on nRF52832 with MAX30205 temperature sensor , i am comparing the temperature with threshold value like this if (m_sample <threshold) then send the data...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
In my application, I am starting BLE advertisement...
Hi,
I'm trying to include AES256 CTR in the ble_app_template project.
What i've done so far: .c files:
- Included the files from /components/libraries/crypto
...
The time to first fix on the Development Board (as well as a prototype PCB I have made) are both around 2 minutes. After getting a fix, is any of the almanac or ephemeris...
Greetings. Is there a way to do information mapping using, for instance, one of the mesh nodes that could act as a client/provisioner to all other nodes and therefore keep...
Hi! I'm working with nRF52 development kit and SEGGER Embedded Studio. I was trying to modify the example given as ble_app_hids_mouse and take all the functions present in...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on System OFF mode.
1...
Hi, i am trying to add additional payload to the Mesh Light Switch example. However, i modified all structs and it came down to the status_handle() function inside generic_onoff_client...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
After wakeup from System OFF (due to GPIO event), I want to validate / debounce...
