hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
I am trying to build my own application that will be updated via DFU UART.
I can update your given example in
examples/dfu/hci_dfu_send_hex/test_images_dual_bank_update_nrf52...
Hi
When initialising BLE in the softdevice, the following value is used as part of enable_params:-
* @brief BLE GATT initialization parameters.
*/
typedef struct...
Hi
I am running SD 132 2.0.1 on nrf52832 rev 1 and i am getting a chip lock reset occurring. (I have cleared the flags as per the errata and reset pin flag is not present...
....\R2D2_build\R2D2_Firmware.hex: Error: Q0122E: Could not open file '....\R2D2_build\R2D2_Firmware.axf': No such file or directory
keil gave me that error. i did research...
Hi
When I used ANCS, there is "bluetooth pairing request" notice shown on the iphone, if choose cancel, then 51822 went to reset, why is that happen?
iOS:10.3.3
NRF51822...
nrf5_SDK 12.3.0
nrf52832
softdevice 3.1
My app used timer for buzzer and led.
This timer call itself, and variable is discount.
This is normal mostly, but in somtimes...
I am working on reading ADXL362 through SPI on PCA10040.I used demo spi in nRF5_SDK_13.1.0.
here is my main code:
bsp_board_leds_init();
APP_ERROR_CHECK(NRF_LOG_INIT...
I am developing on the nRF52 boards with a capacitive sensor. I followed the tutorial in this link and created a custom service with 3 read characteristics. I am able to use...
NRF52 pca10028 DK - SDK14 - Arm GCC (Eclipse) - SD 5.0.0 - bootloader_secure_ble
Using either nRFGo Studio or eclipse to program the flash (it does it with both)
I can...
Hi,
some time ago we ordered 3 PPKs. I tried one under a Mac with VmWare / Win7 with a PCA10040 board. It was working but I got surprising graphics. When I came back from...
Hello,
I am just using the SDK13 on the nRF52832 together with the experimental BDS example (I modified it to the point where it seems to be working fine so far).
Now...
The following does not allow me to define NRF_DFU_HW_VERSION in my makefile, I get redefine errors due to this broken if else in def_req_handling.c:
#if defined (NRF51...
I want to evaluate the nRF52 SDK , but don't get how to install it.
The Getting Started section mentions an MDK installer. However, I cannot find any such installer inside...
Using the nina 112 with nrf52832 SDK 13
I have got a problem with the I2S Interface.
I configured the RESET Pin as normal PIN. Tested with GPIO as Output it worked. If im...
Can we build the FW manually and upload to the Thingy via the OTA uploader? We built the FW, created the DFU, and inserted the .zip file in the iOS app, however get an Error...
