hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
I am a beginner in the study of Bluetooth, and I have difficulty in understanding the purpose of API functions Bluetooth stack. For a better understanding of the system API...
I'm using MCP 3.1 and tried flashing the dongle from it multiple times. I also tried reinstalling MCP, but to no avail. When I flash some Blinky example using mbed it works...
I want to read whole flash memory using for loop and see how long it takes. What i have noticed is that it does not print all the lines. On the other side i ask myself: Does...
Hi,
I am very new to nRF51822 controller. i got some problem with compilation.
i have downloaded SDK v10.0xx and tried to compile blink example from following path.
...
Using Segger Embedded Studio 310i in Linux and SDK12.2.0, I imported the Beacon example project (ble_peripheral/ble_app_beacon) from Keil. Right now I'm trying to make it...
Hello everybody,
RTC0 is used by the SoftDevice. Is it possible to use the current RTC0 counter value as a system time, so that RTC1 doesn't have to run additionally? For...
I created a service with several characteristic values. I can read the values without any problem with the Master Control Panel on my Android tablet, but reading from the...
I am working with nrf51, SDK 11, S130, Keil uVision 5 and have an Application with RTX and want to use DFU OTA.
The bootloader works with the app_hrs_dfu example.
When...
Hi, I tried to enable non-connectable advertising timeout using the macro APP_CFG_NON_CONN_ADV_TIMEOUT in es_app_config.h, but it has no effect. I test this using nRF connect...
Hello,
When I call TASK_START in SPI Master it does not start a transfer. According to registers all seems to be set.
I found what was the problem. When I called TASKS_SUSPEND...
I am using SDk 11. S130 V2.0
What is the equivalent of spi_master_evt_handler_reg ?
I just want to configure my handler to receive the interrupt of the SPI master.
Please...
Hello, I've just purchased nRF52 dev kit and I'm using ble_app_uart example from SDK_12.2 to send/receive data from one pc (which is connected to the dev kit through usb)...
I have been trying to use nRF5 SDK 12 on nRF52 Preview DK by using PCA10040 instead of the removed PCA10036. But example 'ble_app_hrs' that uses SoftDevice S132 v3.0 do not...
Hello,
I am developing a custom board using nRF52. In my previous custom board, the total current consumption is 15mA with DCDC regulator enabled. I want to reduce this...
