hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
We are working on a project that will operate in the MBAN frequency range of 2360-2390mhz. One of our current products utilizes the nRF24L chip, and we were interested in...
hello.
Although example consumes less current when connected, in the project I made, consumption is not reduced even if it connects, what is the cause?
The service seems...
Hi,
I'm trying to write more than 20 bytes to a custom characteristic, from Android (Cordova BLE Central), but this completely crashes my App
APP_ERROR:ERROR:Fatal ...
Problem description :
When using 'Just works' pairing with LESC key exchange peer_manager doesn't allocate buffer for peer public key and doesn't pass own public key to...
Hello,
I want to know what is the correct way to use GPIOTE while my softdevice is running.
I have referred the example of pin_change_interrupt that is provided with SDK12...
I am trying to start scanning for devices.
I have changed from the example (ble_app_mulitlink_central_s130_pca10028) only
clock source to NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM...
Hi,
I want to know that how if we have Beacon on one side and Development kit on another side so it is possible to communicate them if they are using different services...
I'm using nRF SDK and trying to write firmware to my prototype device. However, nRF SDK doesn't detect my prototype device. I checked the power supply to my prototype device...
Hi,
I am testing example from sdk, 12.2.0, ble_app_uart, nrf52832
And i frequently get a strange behaviour where i don't get a response. And the connection is terminated...
Hello,
I'm trying to set my device on DFU mode by an android mobile application without success.
I'm working with nrf51822, sdk10, softdevice 8.0.
I subcribe to the...
Hi.
I'm using PCA10028, SDK12.2.0, S130 as central.
As I know "sd_ble_gap_tx_power_set" function let me set Advertising Tx power.
How can I set Tx power if i want to...
Hello,
I am going my project with NRG51822 in SDK 11. I build a android app that can connect to my device and access vendor specific service.
My device dedicates one...
Hi, All,
I'm testing multi-connection central function.
And I am struggled in getting relation of address.
AFSK, there are several types of address in BLE.
I found...
Hi.
I'm using nRF51822AC, SDK12.2.0, S130 as central.
After "sd_ble_gap_connect" function, how can I stop this function before connection?
I hope your reply.
