I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I use softdevice s110 7.3.0 and SDK version 7.2.
Some times softdevice call app_error_handler with:
error_code 0xDEADBEEF
line num - 990
file_name - src\ll_ctrl.s0.c...
Hi,
I try blinky with softdevice example and reconfigure it to support nRF51822AA. I can program my custom board, I can debug as well, but led is not blinking. I have connected...
Hi,
I want to set the advertising interval to 10.24 sec.
I changed the value of APP_ADV_INTERVAL to 0x4000.
But when i try to discover my device using MCP, it is not...
I'm trying to track down an intermittent bug in programming our Nordic board. So, I'm having to laboriously reconstruct the SWD transactions and understand them.
A transaction...
I use nRF51822 Model in my project that I need to run bluetooth advertising all time. And when I measured current, I found 1mA that is not enough to run for 1 year by just...
Hi,
My project include two MCU with n51822 and STM32. I expect upgrading STM32 application firmware by n51822 DFU function. Do you give your advice to implement it by modifying...
Hi All,
I am struggling getting my N548 module to transmit any ANT+ ...
I have tried the Cycling Power Sample Application (S310)
And the Cadense / Speed (S210) Sample...
Hello,
Is there any delay between when the reset pin is driven low and the actual reset of the chip. Would it be possible to sense the reset pin and perform some quick...
I am designing an nrf52 based device running at 1.8V. To debug the device I was planning to use debug out option of the nrf52 preview DK. However, I just find that, the debug...
I'm trying to follow the code from one of your examples, specifically ble_beacon in SDK 8.0 and eventually I get to a point where I'm not sure what's going on so I figured...
Hello,
I have question. I using examples with nRF51-ble-peripheral-bond-handling with bls_service (PCA10028) and i have problem with unnecessary connection. I want that my...
I'm referring this blog on getting started with nRF51822 and in this same blog, there is a link to a video by Nordic on Introduction to Bluetooth Smart and after watching...
I have two STM8s105 MCUs and two NRF24L01+ modules. Set one as transmitter:
CONFIG: 0x3A
EN_AA: 0x00
EN_RXADDR: 0x03
SETUP_AW: 0x03
SETUP_RETR: 0x00
RF_CH: 0x00...
Hi
I used the boot loader example successfully on the nrf51DK board.
Now I want to use it on my custom board. So I recompiled the boot loader code, with 1 difference:...
