hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
in sdk 4.3, I used two different ways to know it is read first time(in factory)
NRF_ERROR_NOT_FOUND from ble_flash_page_read to indicated first time it reads
0xff...
I have 3 questions:
1. How to set device to non-discovery mode?
2. Once the device is in non-discovery mode, How can host connect to it?
3. Can I use Master Control Panel...
Hi sir
On your Beacon kit, we found it was used external 32.768KHz at 20ppm.
Question is on iBeacon usage, is a external higher precision 32.768K crystal necessary ? ...
Hello,
I'm working on an ultra low consumption purposes with which NRF51822 commnunique in BT4 with softdevice version 5.2.1.
I compile with GCC 4.7 2013q1. Unfortunately...
Hi
I've have customized a state machine and output patterns for the nrf8002 using the development kit. Now i have my own pcb design and I'm aiming to build a small prototype...
I installed master control panel and plug a PCA10000(usb dongle). The panel discovered the dongle.But once i press "start", an error hanppend:
"ascii" codec can't decode...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi there,
Im wondering if its possible to implement a proximity monitor with the new s120. Having one nrf51822 acting as a central and several (up to 8 I guess) nrf51822...
Hello,
at my current project I send a lot of data from one evalboard to another via proprietary Software.
Now I want to send that data via Bluetooth LE from one evalboard...
I would like to confirm the availability of the nrf51822 with DC/DC.
Should the nrf51822 with DC/DC be used in new designs? Will it continued to be available in 2015 and...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
