We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hi, i'm working a BLE gateway with NRF52DK and S132 by using the demo example central uart.
The peripheral equipement advertise manufacturer data like this:
0x0001 during...
Hi there,
I am new to the Bluetooth mesh and I am learning about it. I have some questions about Bluetooth mesh. I hope you will help me with this.
Please pardon me...
Hi
I am trying to implement the communication between nrf52832 dk and nodemcu esp8266 over i2c.
My i2c code in nodemcu is working fine as I had tested the communication...
Using latest download of nrf Command Line Tools and a J-link Plus unit with Tag-Connect interface. Power on, all connections seem good. Trying to upload a .hex file through...
Hello, I am trying to implement some Bluetooth mesh functionality on my Thingy:52, and it's quite a daunting task.
I am using the mesh sdk v3.1.0 thingy:52 sdk v.2.1.0 and...
Dear All,
Could some one help to answer my commented questions below ? thank you so much !
1.
//Definition at line 743 of file hal_nrf.c .
uint8_t hal_nrf_read_reg...
Dears,
I am trying to implement a peripheral device which behaves like this:
1. within 30 seconds after powered up, the device can be discovered and connected by any other...
Hello,
I am using BLE+MCU MBN52832 module and i am facing one issue while programming my application.
I am uploading the hex file using nrfGo Studio and when i try...
Hi Nordic:
We are using mesh-sdk2.2, our application need a device can subscribe many group address, at the most we need 16 subscribe address in a model,
1. I'd like...
Hi all,
I get a really weird issue developing on the smart remote 3 project.
I work with my own hardware design, and as I want a specific behaviour I disabled power_management...
Dear friends,
Thanks all for your support.
I have used a button as a input to detect button press, while at the same time I am using the button as a system wakeup. ...
I'm using nrf51822 , softdevice S110 and the SDK10 . Im reading data from the sensor mpu9250 using i2c at 400Khz( Maximum) frequency. It taking more delay than expected to...
Hi!
I have been following this process to develop using armgcc and Eclipse: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/development-with-gcc-and-eclipse...
Hello,
I have been working to manipulate GPIO.
I succeeded to turn on and off P0.02 ~ P0.05 (LED 1~4). However, I cannot get P0.00 and P0.01 to get work.
GPIO IN seems...
