I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I run eraseall but the following error shows up. how can I fix it?
nrfjprog -f nrf52 --eraseall --log ERROR: JLinkARM DLL reported an error. Try again. If error condition...
Hi,
We have a requirement of reading the BLE Advertising name from flash instead of predefining it in as a MACRO. I saw in the notes it says to use ble_gap_cfg_device_name_t...
Hi. I have just updated to the latest nRF Connect software for windows (v3.0.0), and the latest programmer app.
However now it won't connect to my PCA10056 dev kit (see...
Today I was playing around w/ my nRF9160DK 0.8.2 and messing around w/ the Asset Tracker application. I edited the proj.conf file in order to attempt to get it to connect...
I want to read data over uart from sensor, advertise the value go to idle mode and wake up on rtc timeout to do the same thing again.
when I try to read data over uart from...
The nRF52832 chip and SDK12.3.0 implement the buttonless DFU function.
First, as you are guided by the DK board, you have already completed the tutorial.
I tried to run...
nRF52832_XXAA, nRF SDK 14.0.0, SoftDevice 132 v5.0.1
We run a single service with 2 characteristics: one for "target to host" and the other for "host to target", where the...
Help ！
I use ANCS need change ATT MTU to more , but I met an incredible thing .
just change NRF_SDH_BLE_GAP_DATA_LENGTH to 189 & NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 185
...
Hi,
I was doing some current measurements and tried to reconnect my DK to my computer to put a new program on it. When I try to Connect J-Link, I get an error that says...
the link infocenter fail to download in:
(General PCB design guidelines for nRF52 series)
https://devzone.nordicsemi.com/nordic/short-range-guides/b/hardware-and-layout...
Hi,
Do you have a drawing of a recommended PCB layout footprint for the nRF9160?
I found a link somewhere, but the page didn't exist.
I need a drawing - not an Altium...
As i an trying to establish LTE connection using nRF9160.but i want to use external antenna because i will place nrf9160 module in metal enclosure. please suggest best antenna...
Hi pals!
I'm trying to do the throughput example with using 2 nrf52840DK. I downloaded SDK15.0.0 and I'm using ble_app_mtu_throughput example under ble_central_and_peripheral...
Hello there,
I've been following a guide Installing a 6LoWPAN enabled Linux kernel and required modules as a part of setting up a BLE 6LoWPAN border router on Raspberry...
I'm working on an NRF52832 product that will be intermittently powered, and the supply rail may fluctuate slowly, drifting above and below 1.8V.
I saw this post:
https...
