hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
As I working on a new project I am writing the code to support the new SDK driver structure and not including any "legacy" code support.
This highlights the fact that the...
I have a custom board with nrf51422-QFAC, used with SD 130 and SDK 12.3.0. My firmware consist of ble_app_hids_keyboard example modified. Schematics are attached below.
...
Hi all,
I using 1 Provisioner provisioning for some Nodes (light switch server) . If I have 5 Nodes in mesh network
I want to remove Node 4 from network and then add it...
I am working on a BLE peripheral (nRF52832 & SDK 15) which uses the Peer Manager to handle encryption and bonding to a previously existing central device. Sometimes bonding...
I am using the Segger Embeded studio and wondering about the SWO output.
I know I can load code and set break points with just SWDIO and SWDCLK.
So with RTT do I really...
HI all,
I'm working on the nrf52840, and I've tested this on the devkit as well as on-board on the product I'm working on. Using the saadc, if I tie my AIN line to VCC...
My use case initially is a single central sensor server powered from the mians and serving by BLE one battery-powered peripheral that has one of the commonly available st7565...
Hi,
MacOS serial device name is changings all the time when the nrf52 DK Eval board is re-powered. Meanwhile I have /dev/tty.usbmodem49, counting up. Next time I re-power...
We want to be able to download a firmware image into external flash through multiple paths (wireless or wired -only one path is used at a time) then program that image into...
Macbook pro mid-2014
High Sierra 10.13.5
I get the following message when trying to select the PCA10028 on the serial port:
2018-07-06T22:53:49.427Z INFO Application...
Hello all,
Thanks to the wonderfull nrf connect android app, I've been able to setup a BLE peripheral to broadcast the standardised service for "Location and navigation...
I'm digging into OpenThread, using the NRF52840 DK. I find myself spending most of my time trying to figure out module dependencies. Is there any way to quickly get all the...
I was experimenting the nRF connect android app and switch to the DFU service mode. But now, i am not able to switch it to the default mode. kindly help..
Hi,
In softdevice spec, we have the following figure.
However our bootloader code shows that MBRPARAMADDR is 0x7E000 while BOOTLOADERADDR is 0x78000. In this case...
Hi,
I got in trouble with my DK-52.
I normally use it attached to my iMac and everything work fine.
Since, I need to make some programming from another mac (macbook...
