hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi. When i use ble_app_uart i have problem with my device over uart. It does not response to my commands.
I'm using custom pcb based on nrf52 with nrf UART v2.0 android...
I have moved on to SDK12. But one old project using SDK10 now requires a 128 bit UUID.
I keep getting hard fault when I add UUID.
I noticed that there is no vs_uuid_count...
Hi Team,
I am using nRF5_SDK_11.0.0_freertos_dfu_060516.zip SDK. I have added NUS service with UART configurations in this code successfully.
When I am commented the DFU...
We have both nrf51 and nrf52 running DFU.
How can I identify on the mobile application side whether I'm connecting to nrf51 or nrf52?
They will need to get different firmware...
Hi,
Is it possible to know which type of advertising packet is being advertised by the slave i.e whether it is a connectable or a non connectable advertising packet by...
Hi,
So I have a HEX file with unit specific data that I upload to 0x00062000. This data is about 80kb so it leaves some space incase I need a bootloader in the future....
Hi:
I want to bond and change dev name and storage.
This is my storage dev name init code:
void my_flash_init(void)
{
uint32_t err_code;
pstorage_module_param_t...
Hi all,
i'm using an app_timer.
I need to use three timer for debounce of three button. In my case i have to discriminate the push of three button at same time. When all...
Hello Community
I have read the following threads:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
In order to know how to discover my services, including...
Hi
Does the CryptoCell in the nRF52840 support secp256k1?
In this documentation it says at one point Koblitz curves using fixed parameters, up to 256 bits, are supported...
I used to do with the iso7816 run on nRF51822 SDK9 and S110_v8.0. However,as the BLE stack is running, the iso7816 interface clock signal is abnormal. as the picture below...
Hello!
I have the board PCA10040 (nRF52 DK).
I designed two different programs:
SPI: I'm using the SPI communication to communicate with an external sensor (accelerometer...
Hello, I am working on a project that involves the implementation of a wireless temperature sensor. so, i bought the DS18b20 digital temp sensor and tried to apply the code...
hello friends:)
i have some problem during making my products,
it's an a interface board with ble that generates UART signal for other board
and i made an schematic with...
