HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
After programming the Ble_app_uart to the nrf52832, I am sending a 100 Bytes of data from my UART Port to Nordic chip and this data is transferred over BLE to my Phone. I...
According to Table 19 in the nRF24L01+ datasheet, writing to any of the 32 command registers is "Executable in power down or standby modes only". This caveat is also repeated...
Basically I want to get a 8 byte long MIC when using the AES CCM encryption. From the product specification it does seem like I can only get a 4 byte MIC, is that correct...
Hello,
I try to flash my dev card nrf52 with the program ble_app_uart
Or a program ble by cons I can flasher by other program (pin change in), I do not know from where the...
I created an characteristic that has MAX_Length = 20 Bytes characteristic.
And When I'm trying to write less than 20bytes on this Characteristic, It Always send with 20Bytes...
Is it OK to send multiple packet continuously over nus at below way without waiting for packet transmit complete?
i=UserUart.RxBuf[1]+2;
index = 0;
while(i>0)
{...
Hi,
I'm using nrf51822 Ek kit and running ble_app_uart example,when i want to send any character or integer it Received like a string only,but i want to send only single...
Hi,
this question is more about iOS than nRF, but there's probably here some experience around this subject.
First the context : We have a product based on nRF51, S110...
I compile a .bin file for DFU. The bin file is 62020 bytes. I create the zip file for DFU, it is 62909 bytes.
If I extract the zip file, I get the bin file (62020 bytes...
We are currently designing a prototype board for our product using the nRF52832. We need to calculate the transmission line with on a 4 layer PCB. The stack-up looks like...
I am trying to use your swift iOSDFULibrary cocoapod. What I am doing is the following. I have a library written in swift. That library is where I have your iOSDFULibrary...
As Bootloader IROM starting address 0x78000 and size 0x6000 is same in SDK 13.0 and 12.2.0 expecting to update Device firmware (BL+SD+APP) from 12.2.0 to 13.0.0 SDK.But in...
I use SDK9 nRF51.
I use white list. When I want to delete all bounded devices, I call this function. But it doesn't work. It not deleted.
Why I can't to delete bounded devices...
Hi,
I would like to know which is the difference between using a Softdevice or not.
Looking at the blinky example, the two versions are provided. The "main.c" file is...
