hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi all,
I am thinking of using a GPIO pin's "SENSE LOW" to wake up my device from SYSTEM OFF mode.
In order to avoid the device keeps waking up in case the pin stays low...
I am using an nrf51822 DK with a (so far) very simple code along:
main()
{
//... init I/O
run();
}
Inside run:
run()
{
uint32_t retval = NRF_SUCCESS;
...
Hey,
I recently got the nrf52 DK and tried to make use of the app_button library to have easy to use debouncing.
As far as I understood the library, the event should be...
Hi,
i have a problem withr the example "BLE ATT_MTU Throughput Example".
I flashed the soft devive with nRFgo Studios. Now I want to flash the example, but i got following...
I have want to make application where beacon sends data to NRF52 and NRF52 to PC.
But if for example, the connection between NRF52 and PC is through bluetooth instead to...
Hi,
I have bought a new nrf52840 PDK. I have gone through the PDK user guide and I came to know that we can use qspi pins as gpios by cutting the Solder bridge connections...
Hi All,
I am getting following error while compiling template example with DSP CMSIS library in IAR.
Fatal Error[Pe035]: #error directive: "Compiler generates FPU instructions...
Hello,
I have a question regarding AVDD(35/36) pin. I am using nRF51822 QFAA package. And the reference circuitry on the datasheet uses a 1.0nF capacitor between AVDD and...
Hi, my first post here.
I'm a undergraduate student and newcomer to this field. I've some programming background but few in electronics and embedded systems (so probably...
Hi all,
Is there any DFU example using dual bank to the SDK 12.2? The secure bootloader example is for single or dual bank? . Sorry for the question it is no clear to me...
I have purchased nRF51822 Evaluation Kit.
So I should be able to download Android code. Correct?
But when I go to
www.nordicsemi.com/.../nRF-Temp-for-Android-4.3
...
Hello,
When I try to use the DFU function, I received 8202 error from nrf Toolbox.
My environment is as follow:
SDK version: 12.2.0
SoftDevice version: S132 3.1.0.
...
I got pca10040 dk and I am trying to run the code that was sent to me earlier by one of nordic employee. I could compile it without errors but I cant see any advertising data...
Hi,
I have a problem that when formatting an uSDcard from ext4 to fat32 it gets with both file systems.
In my code I use the FAT FS library [http://elm-chan.org/fsw...
